0
What else can I help you with?
Where is the iat sensor on a 1993 geo tracker 16 valve 1.6?
Its on the Air box
How many valves does a 1991 Honda CRX have?
it should have 16 i know first gen had 12
Where is the IAT sensor at?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburator cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
Where is the IAT sensor located?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburetor cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
Where is Iat sensor at?
The IAT sensor measures the temperature of the intake nmanifold. The ECM uses this sensor reading to set injection timing and adjust the air-fuel ratio. If the fuel mileage and power output of you engine seem low, some owners have found improvement in EGT, fuel economy, and power after cleaning carbon from the IAT sensor in at the rear of the intage manifold. Engine with exhaust brakes are particularly prone to IAT sensor fouling because soot is blown back into the intake during valve overlap. The only tool you need is a 3/8" ratchet with a 6" extension and 13/16" socket. View of IAT from above battery Closer view of the IAT sensor The IAT sensor is found on the driver's side of the engine, almost at the back of the intake manifold. Unplug the electrical connector from the sensor. You will need to spread the connect tab away from the sensor body to unplug the sensor. After the connector has been removed, use a 13/16" deep well socket, 6" extension, and ratchet to unscrew the sensor from the manifold. Photo of a dirty IAT sensor The sensor on the left had 20,000 miles on it, and it was covered with soot. After a shot of carburator cleaner, you can see the sensor element inside the cage. Screw the clean IAT sensor back into the manifold, torque it to 10 ft-lb, and reattach the connector. Photo of a clean IAT sensor Normal IAT Sensor resistance values: Temperature Resistance 30� 40K 32� 30k to 36k ohms 76� 13K ohms 77� 9k to 11k ohms 81� 6.87K ohms 122� 3k to 4k ohms 130� 4K ohms 167 600 to 675 ohms 212 600 to 675 ohms Replacement Sensor: Cummins PN 3408345, around $28. Dodge PN 05014197AA Sensor, Temperature (SEN, TEM), around $18.
What day of the week was April 16 1991?
April 16 1991 was a Tuesday.
What day of the week was 16 march 1991?
March 16, 1991 fell on a Saturday.
What are the release dates for Night After Night - 1989 1991-01-16?
Night After Night - 1989 1991-01-16 was released on: USA: 16 January 1991
What are the release dates for CBS This Morning - 1987 1991-12-16?
CBS This Morning - 1987 1991-12-16 was released on: USA: 16 December 1991
Will a CRX D-16 transmission bolt on to a B-15 engine?
there's no b15 Honda engine, if you meant d15 it will fit
What are the release dates for The Arsenio Hall Show - 1989 1991-04-16?
The Arsenio Hall Show - 1989 1991-04-16 was released on: USA: 16 April 1991
What are the release dates for One Night Stand - 1989 1991-02-16?
One Night Stand - 1989 1991-02-16 was released on: USA: 16 February 1991
