0
Where is the switch located on a 1998 Chrysler sebring convertible to reset the service engine soon light?
There is no reset switch. It is reset with a OBD scan tool after the repair.
UNPLUG THE BATTERY FOR ABOUT 15 TO 20 MINUTES AND IT WILL RESET ITSELF. ALSO YOU CAN GO TO ADVANCED AUTO AND THEY WILL RESET IT AS WELL AS READ THE CODES ON IT IF OU HAVE ANY AND LET YOU KNOW WHAT CODES THE CAR IS THROWING
What else can I help you with?
What is the timing belt service interval on a 2000 Chrysler Sebring JXi convertible with a 2.5L engine?
100,000 miles.
How do you replace the windshield on a 1996 Chrysler Sebring convertible?
Replacing a windshield on a modern car is not a DIY job, besides, a broken windshields are covered by your insurance with no deductible. Call a Automobile glass replacement service and have them replace it.
Where can i find Chrysler sebring wiring diagrams?
Chrysler Sebring is a great brand of car. Wiring diagrams are great use for mechanics. They could be found at local service dealers or auto parts stores.
Where is the leak detection pump pressure switch located on Chrysler Sebring?
The leak detection pump pressure switch is located next to the service vacuum supply. It will be connected to the LDP filter and below the EVAP canister.
What does a tune-up cost for a 2004 Chrysler sebring convertible?
The cost of a tune-up for a 2004 Chrysler Sebring Convertible can vary depending on the specific services included, the location, and the service provider. On average, a basic tune-up for this vehicle may range from $200 to $800. This typically includes replacing spark plugs, ignition coils, filters, and checking and adjusting ignition timing and fuel mixture. It's recommended to consult with a certified mechanic or dealership for an accurate quote based on your vehicle's specific needs.
Service engine soon light is on on 1997 Chrysler sebring convwhat needs done?
Have it checked for codes, That is the same as the check engine light.
The transmission on a 2007 Chrysler Sebring suddenly seems to be stuck in one gear What should you do to fix it?
Take it to a service shop and have the trans checked for codes.
Where is the tensioner pulley on a 1997 chrysler sebring?
On a 1997 Chrysler Sebring, the tensioner pulley is located on the front of the engine, typically near the serpentine belt. It is mounted on the engine block and is responsible for maintaining tension on the serpentine belt that drives various accessories. To access it, you may need to remove any components obstructing your view, such as the engine cover or other belts. Always consult the vehicle's service manual for specific details and guidance.
How much transmission fluid is in a Chrysler Sebring?
Service fill approx 5 quarts. Dry fill approx 9 quarts. Mopar ATF+4
How do you properly change the coolant and thermostat on a 2000 Chrysler Sebring convertible with a V6 2.5 liter MPI engine?
Usually removing the radiator drain plug or lower radiator hose. Make sure to have a drain pan large enough to hold the coolant. The thermostat is usually on the upper radiator hose, but shouldn't need replacing unless it is defective. Better yet, get yourself a Chilton service manual for the Sebring, they aren't expensive and well worth it.
Chrysler sebring egr valve location on 2.4 engine?
The EGR (Exhaust Gas Recirculation) valve on a Chrysler Sebring with a 2.4L engine is typically located on the intake manifold, near the throttle body. To access it, you may need to remove any engine covers or components obstructing your view. It's important to disconnect the battery and any electrical connectors before proceeding with removal or replacement. Always refer to the vehicle's service manual for specific guidance and diagrams.
Where is the leak detection pump on a 1999 chrysler sebring lxi coup?
Service manuals might tell you it is under the passenger side headlight, however the one in my 1999 JXi convertible is actually on my fuel tank assembly. What you'll want to do is look for your EVAP canister (which is a rectangular box about 6inx6inx3in or so and has 3 fuel-safe rubber hoses attached to it). The LDP should be near that.
