answersLogoWhite

0

Don't do that too often. If the starter Bendix is not fully engaging the starter gear into the flywheel, you could be wearing the flywheel. That could be expensive. Remove the starter and inspect the flywheel. Slowly turn the flywheel by hand and inspect the entire circumference of the gear.

User Avatar

Wiki User

19y ago

What else can I help you with?

Related Questions

How to set clock on 1985 Buick LeSabre?

If I remember correctly, you have to pull out the radio buttons that don't correspond to #1 through 6. Hold it out for a while and it will begin to change the hour or the minute.


How do you remove and replace rear air shocks on a 2002 Buick La Sabre?

The 2001 Buick LeSabre rear shocks are held in place with a retaining bolt on each end of the shock. Remove the retaining bolts and the old shocks will come off. Reverse the process to install your new rear shocks.


What are some types of cars that begin with the letter L?

· LaCrosse (Buick) · Lamborghini · Lancer (Dodge) · Lancia Lambda · Land Rover · Laser (Plymouth) · Le Mans (Pontiac) · LeSabre (Buick) · Lexus · Liberty (Jeep) · limousine · Lincoln · Lotus · Lucerne (Buick)


How do you install ac in 1995 Buick Lesabre?

To install air conditioning in a 1995 Buick LeSabre, first ensure you have all necessary components, including the AC compressor, condenser, evaporator, and associated hoses. Begin by removing any components obstructing access to the engine bay, then mount the compressor and connect the refrigerant lines. Install the condenser in front of the radiator, connect the evaporator to the cabin, and ensure all electrical connections are secure. Finally, recharge the system with refrigerant and test for proper operation.


How do you change the brake pads on the rear of a 2002 Buick LeSabre?

To change the rear brake pads on a 2002 Buick LeSabre, begin by safely lifting the vehicle and removing the rear wheels. Next, remove the caliper by unbolting it and carefully sliding it off the rotor, ensuring to support it to avoid straining the brake line. Replace the old pads with new ones, ensuring they are properly seated, and reassemble the caliper. Finally, reattach the wheels, lower the vehicle, and pump the brake pedal to seat the new pads before driving.


How do you replace the heater core located on a 1990 Buick LeSabre?

To replace the heater core in a 1990 Buick LeSabre, begin by disconnecting the negative battery cable and draining the coolant from the radiator. Then, remove the dashboard and the center console to access the heater core housing. Disconnect the hoses attached to the heater core, remove the mounting screws, and take out the old core. Install the new heater core by reversing the removal steps, ensuring all connections are secure before refilling the coolant and reassembling the dashboard.


Car that begins with L?

lamborgini le mans (Pontiac) Lincoln Lafayette lancia Lexus


What transport begins with r?

Rabbit (VW), Range Rover (Land Rover), Regal (Buick), Reliant (Plymouth), Renault, Rendezvous (Buick), Rivera (Buick), Roadmaster (Buick) and Rolls Royce are car models. They begin with the letter r. Railways, Routmaster Bus and Rickshaw are all means of transport that begin with r.


What types of transportation begin with the letter r?

· Rabbit (VW) · Range Rover (Land Rover) · Regal (Buick) · Reliant (Plymouth) · Renault · Rendezvous (Buick) · Rivera (Buick) · Roadmaster (Buick) · Rolls Royce


Car names that starting with the letter l?

LaCrosse (Buick), Lada (Russian auto), Lamborghini, Lancer (Dodge), Lancia Lambda, Land Rover, Landmaster (Hindustan Motors), Laser (Plymouth), Le Mans (Pontiac), LeSabre (Buick), Lexus, Liberty (Jeep), Lifan (Chinese car), Lincoln, Lotus and Lucerne (Buick) are car models. They begin with the letter L.


How do you replace VW Ghia ignition switch?

Begin by removing the retaining ring at the top of your ignition switch. The ignition switch will slide out and you can remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.


How do i change the ignition module in a 1998 suburban?

Begin by removing the wiring harness from your 1998 Chevrolet Suburban ignition module. Remove the ignition module retaining screws. Reverse the process to install your new ignition module.