0
Why will your ignition on a 1976 corvette not return to the locked position?
Wiki User
∙ 12y ago
Could have something to do with the shifter not going all the way in to park. The key may be excessively worn, the pin that locks the steering wheel may be hung up, the lock and tumbler may be bad....
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What makes key not turn to lock position on a 2006 Chevy Cobalt?
If the battery is dead it will not allow the key to return to locked position. Thus trapping you key in the ignition.
Why do you yell Dismount after sex?
You have arrived at your destination. Please return your partner to an upright, locked position.
How do you change camshaft position sensor 2007 f150?
Remove ignition transformer to reach it. There should be 2 camshaft position sensors on the 5.4L engine - visibly on the front right cylinder head and the other visibly on the front of the left cylinder head. Remove ,Replace, then return ignition transformer.
How do you reset the driver information panel on a 1998 Buick Regal after an oil change?
Use the ignition key to place the ignition in the "off" position. While the ignition is in the off position, press the gas pedal to the floor three times. Place the gas pedal to the floor one more time and hold on the floor for at least ten seconds. Release the pedal and return the ignition to the lock position. The oil life indicator in the driver information panel should now be reset at 99%.
How do you replace a headlamp on a 1992 Corvette i can't get the headlight doors to stop in the halfway position?
to replce the sealed beam headlamps on a c4 corvette you must turn the headlights to the second on position and while they are still turning you must quickly return the switch to the halfway position (side markers only position) and this will freeze the headlights in a position where thay can be accessed. although this is inconvenient it is the only way to do it. (it may take multiple tries to get it into best position but now that you know the technique it shouldn't be hard. once you have the assembly in the halfway position the rest iis very simple. remove the 4 screws that hold the outer cover to the assembly and place to side. once this is done only 4 screws remain to remove to complete. remove the 4 screws from the chrome trim ring and the headlight will slide out. after removing ring and unplugging bulb, reinstallation of your new 6054 headlight is simply the reverse. best of luck felllow corvette owner:) -Coty- owner of : 84 z51 corvette 96 Lt4 corvette
How do I fix a 2003 grand prix ignition that will not return to original start position when you turn the car off?
Push on the gear shift putting pressure forward or wiggle it as you turn the key.
The ignition key will not return to the lock position and is stuck in the steering column what happened and how do you fix it?
The key is worn out , u need to try pulling out w/pliers ,use a newer key
What is the code on the locked coffin in the return to Halloween escape game?
1232
Why does the ignition not return to normal while starting the car?
Most likely the return spring is weak, or broken...
The rear wiper motor for your 1997 Jeep Wrangler Hardtop has three wires When you connect only two to a switch you are able to operate the wiper Why are there three wires?
The three wires are the ground wire, the hot wire that runs through the switch and is energized only when the switch is in the on position and the third wire which is energized anytime the ignition switch is on. This circuit allows the wiper arm to go to the "park" position when you turn the wiper switch off. If you turn the ignition switch off while the wiper is in operation it will stop immediately and not continue to the "park" position. When the ignition switch is turned on again, the wiper will return to "park".
How do you delete a hard return code in a Word Perfect document?
Go to, "View all characters," position the cursor before the Hard Return character, and press delete. Or, position the cursor after the hard return character and backspace.
Reset clio immobilizer?
Ensure the battery is charged. Unlock car on the key fob. Turn key in ignition to position 3 (ignition fully on but not at start) for 30s to 1 min. Return to fully off for 30s. Back to position 3 for 30s, to off for 30s. Then turn key straight to start position, engine should now catch on the started. This should reset the imobiliser. Needed after the car is jumped from another car if the battery has run flat because its french and so is afraid of work. Hope it works for you Matt
