answersLogoWhite

0

yes.. most parts are good thru years 1989 - 1995.. He is correct, the only parts that are different are the engines, the transmissions, and the headlights. Most simple parts that dont relate to those should work.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

How do you replace or remove the passenger side window on a 1995 lebaron convertible?

To replace or remove the passenger side window on a 1995 Lebaron convertible, start by lowering the window fully. Remove the door panel by unscrewing any fasteners and carefully prying it away from the clips. Disconnect the window motor and any wiring, then remove the window glass by unscrewing the window regulator bolts. Carefully lift the window out of the track, and to install the new one, reverse the steps.


In a 1991 lebaron convertible can the plastic window be replaced by a glass window?

Yes! If you have a zipout window. It will require top half open. Then the lower panel removal, re-stapling of the new meterial to the panel. Good luck tight fit.


How do you replace the windshield on a 1996 Chrysler Sebring convertible?

Replacing a windshield on a modern car is not a DIY job, besides, a broken windshields are covered by your insurance with no deductible. Call a Automobile glass replacement service and have them replace it.


Does a Chrysler have bullet proof glass?

No.


How do you replace rear window in 1979 super beetle convertible?

The rear windows on a 1979 Super Beetle convertible are replaced by prying away the rubber molding holding the glass in place. The glass can then be slowly lifted away before new sealant and glass is installed.


How do you remove and install LeBaron rear glass convertible 1995?

need to remove top .rear glass comes attached to a black piece that attaches to frame and rear of convertible storage area .It is a job .You have to remove screws and staples and then screw and staple back in .If you are set on doing it ,I would suggest to get an instruction guide from where they sell rear glass window assemblies or convertible tops Careful when you put top back on,material is old and rip easily when stretching and stapling. I replaced my rear glass .I cut a rear glass from a junk yard .I set glass in black frame There is a groove {about an inch and half wide) I put 3M Windshield Sealant in the groove and set window in groove .I,then put Scotch Black Duct tape around glass and black vinyl piece (both inside and outside) It works and no leaks Again The trick was The Scotch Duct Tape The Black one sticks and seals the best .I tried the clear and grey,but they don't stick as well. Good luck


What material was the chrysler building made out of?

Stone, Steel, Glass


How do replace the glass clips on drivers door glass of 1995 grand prix se?

how do you replace the drivers window clips on the glass od a 1995 grand prix se 2 door?


How do you refasten the glass rear window on a 2001 Audi TT convertible?

To refasten the glass rear window on a 2001 Audi TT convertible, first, ensure the convertible top is fully lowered. Then, locate the zipper or fastening mechanism that holds the glass in place—this may involve aligning the glass with the top and securing it into the frame. Carefully zip or attach the window, ensuring it is tight and properly aligned to prevent leaks. Finally, check for any gaps and adjust as necessary for a secure fit.


Is it safe to put a decal on a convertible's rear window I have a window sticker for cars that i would like to put on but my car's which is a convertible back window is made of plastic not glass?

I wouldn't.


How do you change glass in drivers door in fiesta?

i dont no


How do you glue a glass rear window on a convertible?

To glue a glass rear window on a convertible, first, ensure the surfaces are clean and dry. Apply a suitable automotive adhesive or urethane specifically designed for glass bonding, using a caulking gun for even distribution. Position the glass carefully, pressing it against the frame to form a tight seal. Allow the adhesive to cure as per the manufacturer's instructions to ensure a secure bond.