How caves are made?

Answer 1

by water and air combining to build pressure

+++

Tht'as not correct and it's hard to see what the respondent had in mind.

Most caves are formed in limestone by naturally-acidic groundwater dissolving it as it passes through the joints, bedding-planes and faults in the rock mass.

Answer 2

How Caves Form in Limestone

That is such a common question on ‘Answers’ I wrote this single reply! The technical terms are introduced by capital initials.

Most of the world’s caves are in Limestone.

Caves need three materials: a soluble rock like Limestone or Gypsum, water and Carbon-dioxide (CO2).

Their host limestone also needs to be of appropriate physical structure and raised into hills, then subjected to reasonably consistent precipitation for many tens or hundreds of thousands of years.

Limestone is a sedimentary rock of which the world’s greater proportion was laid down in warm, relatively shallow, seas. The rock was laid in horizontal layers – Beds – separated by Bedding-planes which generally reflect geologically-brief changes in the environment. The suite of beds is known as a Formation, generally named after its “type area”.

Later continental uplift (tectonic processes) raise the formation along with its underlying rocks, usually tilting and folding it to at least some extent in the process. Since most rocks are brittle they cannot take much stress, and limestone beds crack into grids of fine fractures called Joints. The uplift and folding often also causes Faulting – major breaks with the rock mass one side of the Fault Plane being raised, lowered or moved horizontally past that on the opposite side. (Note: Plane – the “Fault Line” sometimes misused as a political metaphor is that of the fault-plane cutting the land surface.)

Now we have the hills, next we need rain-water that has absorbed atmospheric CO2 to create Carbonic Acid (weak, natural soda water in fact!). It may be augmented by acids from the soil, too. This solvent permeates through all those joints, bedding-planes and faults; flowing very, very slowly under considerable pressure applied by its depth, from its sinks on the surface to its springs at the base of the formation. In doing so, it dissolves the limestone (chemical weathering), creating meshes of tiny micro-conduits that over many tens of thousands of years coalesce and capture each other to form cave passages.

Once this happens, the rate of erosion can increase – though still to perhaps only a few millimetres per thousand years under generally temperate climates.

A cave, or a series within a cave system, that still carries its formative stream is called “Active”, and is still being developed.

Surface changes such as the valley floor being lowered by erosion, or down-cutting within the cave by its stream, changes the water’s route and the original, now dried-out, stream-way is called “Fossil” or “Abandoned”. Such passages may be filled with silt left by floods as the main flow gradually abandons them; or may become richly decorated with Speleothems – calcite deposits such as stalactites and stalagmites precipitated from ground-water still oozing through the joints in the limestone above the cave. In time such passages may start to break down as there is no stream to dissolve away slabs falling from the roof as permeating ground-water attacks the rock above.

In the end, surface lowering of the landscape as a whole, breaches and destroys the cave. Nothing is permanent in Nature!

Caves in limestone are also parts of Karst Landscape. i.e. a landscape developed by the dissolution of limestone, giving surface features like Dolines, Limestone Pavement, and in the tropics, distinctive hills such as those represented in Chinese Willow-pattern images. ‘Karst’ is from the Slavic word ‘Kras’, the name for its world type-area.

@@@@@

The above is purely an introduction to a vastly more complex and subtle series of processes, of course, and you need to refer to appropriate text-books on geology and cave studies to learn them.

The scientific study of caves is Speleology – embracing geology, hydrology, Biology, Archaeology and other disciplines.

Simply visiting caves to enjoy them for their scenery and the physical and mental challenges they present, is called Caving, though you can’t study a cave unless you can negotiate its obstacles. We caving enthusiasts are simply Cavers, throughout the English-speaking world – not “spelunkers”, which appears to be merely rude, USA-only, slang for novices and dilettantes!

Answer 3

Caves can form in a variety of ways, but most caves are dissolutional and are initially formed by chemical weathering of surface rock, usually limestone, by carbonic acid contained in rainwater. As chemical weathering continues, mechanical weathering joins in the fun to further attack and widen joints and fissures in what is usually soluble sedimentary rock. Some other types of caves are formed by percolating sulfuric acid, flowing lava, flowing water in glaciers, wave action, and particle abrasion.

Answer 4

Caves are typically formed through a combination of geological processes such as erosion, weathering, and the dissolution of rock by water. For example, limestone caves are often created by the slow dissolving of limestone bedrock by acidic water over thousands of years. Other types of caves can be formed by volcanic activity, tidal action, or the collapse of underground chambers.