Yes, depending on the reason it is warped. If the thread has shrunk, then you need to cut the thread, and repair at least three stitches on both sides of the cut.
However, if the plastic is twisted, you can correct that by using a steam iron, on a low heat setting. Cover the project with a wet cloth, such as a sheet or t-shirt, and place the steaming iron in it lightly. Then put the project on a dry surface, and cover with a weight until dry. I turn a full coffee can upside down to flatten them.
Check ebay. Mary Engelbreit is currently without a needlepoint stocking manufacturer. I'm sure she'll make them again at some point in the future.
I assume by trouble, you mean with licensing restrictions and rules for specific football teams, perhaps college or NFL teams? I also assume you want to make the helmets and sell them. A way to get around licensing regulations is to make the helmets general and not include the name of the team on the helmet. I do not know if the actual logo would have to be changed a little, too, but I would assume it would have to be. Otherwise, if you wish to make exact replicas of the team logos and names and sell them, you would need to contact the schools or NFL to obtain a license to make them. I got the NFL application once and it was pretty detailed about 10 years ago when I got it, but it is not impossible to meet the requirements. As I remember it, though, it was pretty costly. There also might be a certain number you can make and sell without a license, but I doubt it. I don't think there's a market for premade plastic canvas needlepoint replicas of NFL and/or college football helmets. You could sell them as craft kits, but not premade. How about doing these of the local high school teams? Licensing a high school team's logo wouldn't be expensive--at most a couple dollars payable to the athletic fund per helmet--and I think they'd be popular.
Yes, I have successfully used acrylic paints on plastics without damaging them. Yes, I have used acrylic paints on plastics without damaging them.
If you are painting lettering directly to the plastic, there are single part epoxies that are available, some suitable for outdoor use, that would adhere to plastic without having to use a primer. If you are going to paint the background a solid color, you can use a special primer, formulated to adhere to plastic, then paint it with an acrylic paint which can then be coated with the same type of acrylic paint for any lettering and design.
A woodworking vice is a must woodworkers tool, it clamps wood so you can work on your wood work project without having to worry about holding your wood while you are trying to work on it.
Check ebay. Mary Engelbreit is currently without a needlepoint stocking manufacturer. I'm sure she'll make them again at some point in the future.
About $800 for four stitches in New Hampshire...
No. Administering stitches to a dog is a painful process and the dog might react violently due to the pain if the vet tries to put on stitches without sedating him. So it is best to sedate the dog before trying to sew him up.
Initially it is not a good idea to get stitches wet in the bath or shower. You get stitches when the skin has be cut and during the initial stages of healing, it can disturb some of the fragile structures that are trying to form to aid in the healing. Washing or rinsing the site where the stitches are can remove antibiotics that have been applied to the site to protect it. Although the shower or bath water may be pretty sanitary, it still can introduce some pathogens - bath water more than showers. More importantly though, if antibiotics have been washed away, the environment around you is loaded with pathogens that now have an easier time getting a start at infecting the site of the stitches. Last, but not least, getting the stitches wet means you are also drying out the skin around them. The skin around the stitches is already damaged and removing the natural protections like the natural oils produced by the skin. I suppose it should go without saying that if the stitches are the kind that are designed to dissolve over time then you REALLY don't want them to get wet and dissolve ahead of schedule.
without project management ,the project will be failed..pm:application of knowledge, skill, tools and techniques to project activities to meet the project requirement.project;it has clear start and clear end.from the above definition clearly reveals that without project management thereis no project,without project there is no quality product,without quality product there is no customer satisfaction, without customer satisfaction there is no success ,without success there no brand , without brand there is no identification, without identification ther is no organization........so all under the project management ,.
Yes it can but it must be kept very clean.
they were just like they are with plastic but they were not plastic
Yes, the stitches would cover the hole where your tooth was extracted. This is to help the gums heal without food getting caught in the hole.
don't ask me that if I don't know it. ___________ This is a question for your doctor.
Having 15 stitches on the ring finger can be costly. Each hospital will charge a different amount. If a person does not have insurance, the hospital will work with them on the bill.
Do not burn plastic
Polaris Project's motto is 'For A World Without Slavery'.