There is an article on eHow about painting tub surround. http://www.ehow.com/how_4453501_paint-tub-surround.html
Yes. It must be perfectly clean and de-glossed with steel wool and the paint must be a type that will adhere to plastics.
Try that new Krylon for Plastics only. Sunnyraye
Possibly, if you really cleaned the tub aggressively with lacquer thinner or similar de-greaser.
Use paint thinner .
Enamel paint can be used on porcelain or iron bathtubs with great results, so I'll walk you through this process, just in case you're unsure about how to do this.You Will Need These MaterialsWhite vinegar WaterTowel Palm sander 150-grit sandpaperRespirator mask Plastic bag Tape Epoxy enamel spray paint Oil based primer Oil based enamel paint 1200-grit wet/dry sandpaper InstructionsClean the bath tub thoroughly with a mixture of white vinegar and water. The vinegar will help remove any dirt or greasy residue on the tub. Rinse the tub to remove the vinegar and dry it with a towel.Equip a palm sander with 150-grit sandpaper. Sand the inside and the outside of the tub to roughen the surface, this will allow the paint to properly adhere to the bathtub.Remove the fixtures of the bathtub or cover the fixtures with a plastic bag. Tape the bag down at the base of the fixtures to prevent painting them when you paint the inside of the tub.Spray the inside of the bathtub with an epoxy enamel spray paint such as Krylon epoxy enamel paint. These paints are available at most home improvement stores and will resist moisture which is necessary for paint on the inside of a bathtub.5 Paint the outside of the tub with an oil based metal primer such as Rust-Oleum metal primer. Let the primer dry completely.Apply a coat of oil based enamel paint to the outside of the tub. Let the first coat of paint dry and then apply a second coat.Sand the second coat of paint with 1200-grit wet/dry sandpaper used wet. This will help shine the enamel paint.I hope this helps you out with your project! Good luck!--The Violet
Tiles, or good quality paint.
Yes. It must be perfectly clean and de-glossed with steel wool and the paint must be a type that will adhere to plastics.
Try that new Krylon for Plastics only. Sunnyraye
When choosing a mobile home tub surround, important factors to consider include the material of the surround (such as fiberglass or acrylic), the size and shape of the tub, the style and design of the surround, ease of installation, durability, and maintenance requirements.
The steps involved in a tub surround replacement project typically include removing the old surround, preparing the area, installing the new surround, sealing the seams, and finishing with caulking.
If it's a plastic tub surround, I would repair it temporarily with 100% silicon . I would then plan on replacing the surround completely within a month or two.
To replace a tub surround in a bathroom renovation project, follow these steps: Remove the existing tub surround by carefully prying it off the wall. Clean and prepare the wall surface for the new surround. Measure and cut the new tub surround panels to fit the space. Apply adhesive to the back of the panels and press them onto the wall. Secure the panels in place with screws or nails. Seal the edges and seams with caulk to prevent water leakage. Allow the adhesive to dry completely before using the tub.
To remove a tub surround effectively, start by disconnecting any plumbing fixtures and removing any caulk or adhesive. Then, carefully pry the surround away from the wall using a pry bar or putty knife. Be sure to work slowly and methodically to avoid damaging the surrounding walls or tub.
To effectively remove a tub surround, start by disconnecting any plumbing fixtures and removing any caulk or adhesive. Then, carefully pry the surround away from the wall using a pry bar or putty knife. Be sure to work slowly and methodically to avoid damaging the surrounding walls or tub.
To install a tub surround, first measure the area and cut the panels to fit. Clean the walls and apply adhesive. Press the panels into place and secure with screws. Seal the edges with caulk and allow to dry before using the tub.
Tub Surround vs. Tile - Remodeling Forum - Garden Web ths.gardenweb.com/forums/load/remodel/msg1023284914921.html 31 posts - 17 authors - 1 Oct 2011 We have the manufactured marble tub and surround. ... They're not that heavy, but I'd recommend that two people do it, at least with ... made a Swanstone tub surround 'work'...maybe I can save $$ and get mine looking decent. ... lower (i.e. not including his shipping charges) and refunded me the difference.
Tub surround may come in cheap or expensive prices. But why purchase expensive ones when you can purchase a cheap one in a good quality. All you have to do is visit Nextag and look for the cheapest tub surround they offer with a good quality.