0
How do you change or remove the fuel injectors on your 98 blazer vortec 4.3 Water in gas tank and won't run now?
Wiki User
∙ 18y ago
You don't need to replace the injectors. Drain the fuel tank. Reinstall. Put in fresh fuel, and water treatment.
Wiki User
∙ 18y ago
Add your answer:
Earn +20 pts
What do the fuel injectors look like in a 96 Chevy Tahoe vortec?
You can not see them until you remove the plastic upper intake / Plenuem Then you will see small little plastic lines that come off of them, Mechanics call that the spider. There will be 4 injectors on each side of the spider center body./ injector housing.
Where is the fuel pump on a 2002 Chevy S-10 Extreme pickup with the V6 Vortec engine and an automatic transmission?
It is in the gas tank, you will have to remove fuel tank to service the pump.
Your 1993 s10 Chevy blazer is dumping gas into the oil and it wont start what is causing this problem?
sound like you have a 4.3 vortec with a bad spider. it is multiported so inside the plentum of the intake, there is your spider, they go bad and fill up your intake with fuel, then dump it down the valley of the engine.
How do you remove a broken spark plug from a 6 liter vortec 2002 gm sierra 2500?
Keeping the plug wire out of the way, Start the engine. In a few minutes the engine pressure should push out the porcelain center from the plug. At this point you can use a tool called an easy out to remove the threaded part of the plug.
What are differences with block and cylinder heads from 93 vortec 4.3 and a 95 vortec 4.3 and would mixing them cause crank but no start?
I bought a 95 S10 Blazer w/ L35 Vortec and put a 92 4.3 Vortec into it. The blocks a mostly the same. the timing cover flange is different then the 92 or 93 vortec. If u use a block older the a 95 then Put a lot of RTV around the bolt holes on the cover-to-block mating surface. The heads are also different. There is one hole, a knock or coolant sensor, in the 94 and older heads. In 95 the Drivers side has 2 sensors, I coolant and 1 knock sonsor. The 94 and older engine had the knock sensor at the back of the head on the block. In 95 the passangers side head didn't have any major changes. The 95 S10 Blazer(compared to the 92 S10 Blazer has different: timing cover w/ crack sensor, distributor with cam sensor (non HEI-style), 2-sensor holes in drivers side head, Slightly different lower and upper intake. Lower intake has a pin that a distrubutor postitioning arm, It keeps the distributor locked into a certain position. and the upper intake has a bigger hole for the IAC valve's plunger. don't use an older IAC valve from an older 4.3 Vortec, There different. If you can us a block out of a 96 and switch everything else to the 96 block. The 96 has reinforcing ribs from the water pump to the lower corner of the block on both sides. My 95 Blazer runs really nice with the 92 block and rebuilt 95 heads on it. At least until it stalls. The thing warms up and then stalls. I cant find the problem. I have replaces Cap, Rotor, Plug, Wires, Coil pak, Fuel pump, Crank sensor, Both drivers and passengers side Knock sensors, both Coolant sonsors (side drivers head and lower intake sensor). Put a 92 Egr valve on it not the same autozone part#, but it didnt affect the way the engine runs, if anything ran better with the 92 on it( it was cleaner).
What is blazer vortec?
Vortec is the motors name in the blazer and it is a great motor
Is there a fuel diagram for a 94-95 blazer with cpi 4.3 vortec?
There is a fuel diagram for a 94-95 Chevy Blazer with a CPI 4.3 Vortec engine in the service manual. It shows the path the fuel travels from the fuel tank all the way to the injectors.
How do you change a oil sending unit on a 97 blazer vortec v 6 4.3?
how to change a oil sending unit on a Chevy vortec v 6
You have 94 s-10 blazer 4.3 and a 94 gmc jimmy with a vortec The 94 gmc vortec is bad Can you remove the fuel injection from it and sit on the non vortec engine What changes to make it work?
you would need to change the cylinder heads also.See link below
Water in gas 98 blazer vortec Pulled drained cleaned New filter and pumpFuel makin it to bleeder valve but not injectors what do you do?
crank it till starts
Where is the fuel pressure regulator located on a 2000 Chevy blazer with a 4.3l vortec?
It is located under the upper intake manifold. It is connected to the bank of fuel injectors (poppets) bank.
How many fuel injectors in a 2003 4.3 v6 vortec x code?
how many fuel injectors in a 2003 4.3 v6 vortec x code
Where are the spark plugs on a 2002 Trail Blazer LT and how can you change them on your own?
The plugs run down the center of the engine under the coils. You can see the coils after you remove the resonator (Thing that says Vortec 4200)
How do you replace a fan belt on a Chevy blazer 4 x 4 need diagram?
how to change the fan belt on a 1995 Chevy blazer vortec motor?
Where is the oil pump located in a 1994 Chevy blazer 4.3L vortec?
It is inside of the engine oil pan. You will have to remove the oil pan to get to it.
How do you set timing on a 2000 Chevy blazer s10 v6 vortec?
On the Vortec the computer does it all.
How many fuel injectors does a 2003 4.3 v6 vortec have?
6
