Depending on how large it is and if the metal is creased or not, you can simply remove the dent by using s large suction cup and pull it out. If there is an actual crease in the dent, then other methods would have to be used.. Tapping it out from the inside by removing the inner door panel then shaping and finally filling and repainting. OR you could call a local Paintless dent repair company and let them decide the best way. Good Luck.
It depends on the size + type of the dent. If the dent doesn't have a distinct crease it can be popped out many times with a suction cup, tapping around the outside edges. If it is a more serious dent, it will probably be necessary to get behind the dent and pick it out. Sometimes you can make a small hole in the side or bottom of the panel and pick it out with a pry bar, filling the hole with a plug when finished.
i dent know
You can repair a soft dent on an oil canvas painting by soaking a rag in hot water and then placing it on the area at the back of the canvas. Leave it for a while and the dent will disappear as the canvas dries up. Alernatively, use some steam on the area.
Put front of car on jackstands or ramps. crawl under the front, right in the middle of the car... about 2 feet from front bumper should be your starter... Oh, disconnect negative side of battery first... remove wires from starter... remove the black plastic cover to get at the bolts (pull it forward), remove the two bolts holding starter slowly, careful not to drop the starter, they are heavy, awkward, and can leave quite a dent in your forehead...replacement is the reverse of removal...
rent bent cent dent lent sent went
Remove the bumper cover (mounted using a combination of snaps & bolts). Apply a force to each dent in the opposite direction of the force causing the dent. The dent area will often pop back into its original position.
form_title=Dent Removal form_header=Dent removal specialists can remove dents, dings, and hail damage on your vehicle without affecting the original finish. What is the year, make and model of your vehicle?=_ What caused the dent?=_ Where on the vehicle is the dent located?=_ Would you like the dent repainted?= () Yes () No () Not Sure
I have a small dent need to remove it
There are 2 different ways to remove a dent over the rear wheel well of a vehicle. You can either suction the dent out from the outside of the wheel well or get the dent out by hitting the inside of the wheel well.
If the dent is not cressed an average joe can remove the dent by purchasing an easy out dent remover. They are pretty simple to use and the instructions make it pretty basic for any average joe to figure out. However it the dent has a wrinkle or creace in it, it would be much wiser to seek out professional help, that what they are trained to do. Some tasks are not ment for the average person to do themselves bodyshops are trained and have had schooling to master removing and refinishing a dent. If the dent is small yes if the dent is not and is creased seek out a professional.
Sledge hammer and a dent puller.
Compressed air can remove a dent in a car very quickly, Youtube has videos of how this can be done. Another way is to apply dry ice which is a very inexpensive alternative.
Dents in a car can be removed by seeing a specialist, or can be done at home. If you want to remove a dent at home, the best ways to do it could be the hair dryer and dry ice method, or by using a tool such as the Pops a Dent, which is basically a strong magnet which can pull the dented metal back to its original shape.
John Dent Dent died in 1894.
John Dent Dent was born in 1826.
Put it in warm/hot water. I have done this before. The heat cause the air inside to expand and pop it out. The dent will pop out, but the surface still has a slight imperfection from the dent. It won't be as good as original.
There are a number of easy do-it-yourself ways to repair a dent that have worked for people. The best method largely depends on the type of dent. One way is to use dry ice or a hair drier on the dent. This can remove small dents. Another way is to use a toilet plunger to pull out a dent. A third way is to take a hammer to the inside of a dent and gently tap it out. When using any of these methods, one must inspect for paint damage and repair that as well with some matching touch up auto paint. Otherwise, the paint damaged spots can begin to rust.