answersLogoWhite

0

Read the Haynes Repair manual and it states to either use a special tool (looks like flat bar, forked at the end) or to put the crank in the down position, lift a clean shop rag up and directly behind the crank, and pull up until the clip snaps out.

I tried this but still can't see where the clip is that is supposed to be behind the crank.

Anyone else have suggestions??

User Avatar

Wiki User

10y ago

What else can I help you with?

Related Questions

How do you remove the window handle from a 1998 Pontiac Sunfire?

Don't know, would like to know.


How do you remove a manual window crank from the front door panel on a 2001 Pontiac Sunfire?

There is u- shaped flat peice of meltal and it's a window handle clip remover Auyo zone has thewm and they do now cost much! Good Luck!


How do you remove the manual window crank on a 1999 Pontiac Sunfire?

How do you remove the manual window cranThere should be an Allen type set-screw in the base of the handle. It will be recessed, and you'll have to turn the crank to access it more easily. Remove the setscrew, and the handle slips off of the stud. If the window is down, and it begins to rain, you can roll the window up by holding it onto the stud, and turning, or you can use a small pair of vise grips. Just try not to damage the teeth on the stud.


How do you install a window motor on a 1995 Pontiac Sunfire?

To install a window motor on a 1995 Pontiac Sunfire, first, remove the door panel by unscrewing all fasteners and carefully prying it off. Disconnect the electrical connector from the old window motor and remove the mounting bolts to take it out. Install the new window motor by securing it with the bolts and reconnecting the electrical connector. Finally, reattach the door panel and ensure everything is functioning properly.


How do you install your window motor in a 2002 Pontiac Sunfire?

To install the window motor in a 2002 Pontiac Sunfire, first, remove the door panel by unscrewing the fasteners and carefully prying it off. Disconnect the electrical connector from the old window motor and remove the mounting bolts to take it out. Position the new window motor in place, secure it with the bolts, and reconnect the electrical connector before reattaching the door panel. Finally, test the window operation to ensure everything is functioning correctly.


How do you change the window regulator on a 1998 Pontiac Sunfire Convertible?

To change the window regulator on a 1998 Pontiac Sunfire Convertible, first, remove the door panel by unscrewing the screws and gently prying it off. Disconnect the window switch harness and any other connected components. Next, remove the old regulator by unbolting it from the door and carefully taking it out, then install the new regulator by following the same steps in reverse. Finally, reattach the door panel and test the window operation.


How do you replace a rear passenger window glass on a 1997 Pontiac sunfire?

Sure wish there was an answer to this one.


What does a box with sqiggly lines under it mean on the dashboard of a 1995 Pontiac Sunfire?

That should be the window defroster.


How do you take off front speakers for a Pontiac sunfire 2002?

remove the door panel and the window crank (if manual windows) , if auto windows remove the piece behind the door handle and unclip it from the buttons unscrew all screws around the door panel with a regular screw driver once you have done all that u will see the speaker remove it with a star head screw driver


Why won't your defrost work on a 2003 Pontiac Sunfire?

check the fuseor the plugin at the rear window or mabey a broken wire


How do you get the window crank off of a 2005 Pontiac Sunfire 2-door if there does not appear to be a clip?

Trust me there is a clip it is a real cheap wire horseshoe shaped clip, the only way to remove this clip is you need to purchase a tool just for removing clips on window cranks.


How do you replace the driver's side manual rear window glass on a 1996 Pontiac Grand Am SE?

Remove the door panel, then remove the plastic sheeting. Then you can gai access to the window tracking. Remove the two 10mm nuts, that hold the window glass to the upper track. Remove the glass from the door, and install the new one in the reverse procedure.