0
How do you remove the timing belt and crankshaft of 96 Dodge Caravan 2.4 liter 4 cylinder?
Wiki User
∙ 8y ago
The crankshaft comes out of the bottom of the engine with the engine out of the car. Get a manual on your car from AUTOBOOKSONLINE.COM.
sorry, i asked the wrong question, i just need to know how to remove the pully of crankshaft, Thanks!
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
Do you need to change the timing chain when you replace the head gasket?
Not likely. Most timing chains never wear out, and on most engines you do not have to touch the chain to remove the cylinder head.
Does your 1981 Ford truck with a 300 ci motor have a timing belt?
No , actually the Ford 300 cubic inch / 4.9 liter inline ( straight ) six cylinder engine has gears that mesh with each other on the front end of the crankshaft and the front end of the camshaft so it doesn't use a timing chain or a timing belt
What are the sensors on a Ford escort ZX2?
The Crankshaft Position Sensor senses it's position from a toothed timing ring behind the Crankshaft pulley. The CKP is above and to the left of the crankshaft pulley.
What are symptoms of timing belt slips on 2002 Chevrolet s10?
The 02 Chevy S10 with a 4 cylinder or a 6 cylinder does not have a timing belt.
How do you change timing belt on 1995 mercury villager?
While the manufacturer has not recommended a mileage interval for changing the timing belt on a 1998 Ford Contour, experienced technicians recommend changing the belt at 60,000 miles, according to Autodata's timing belt book. The engine is an interference engine, which means that should the timing belt stretch past its useful life or break, the valves will most likely contact the pistons, causing extreme engine damage. This procedure uses special tools that are available at the dealership. 1. Step 1 Disconnect the battery ground cable, using a wrench. Raise the front of the Contour with the floor jack, then support it with jack stands. Remove the right-front wheel, using the lug wrench. Remove the lower splash guard for the engine and the right, inner fender lower splash guard. 2. Step 2 Mark the direction of rotation on the accessory belt, using chalk or correction fluid to draw an arrow. Loosen the accessory belt tensioner with a wrench, then remove the accessory drive belt. Unbolt and remove the water pump pulley and the accessory drive belt tensioner, using the appropriate size sockets. 3. Step 3 Loosen the crankshaft pulley bolt. Number the spark plug wires so you know where they go when you replace them. Pull the spark plug wires of the plugs, then remove the spark plugs. Carefully slide the screwdriver into the number 1 piston hole until it contacts the piston. Turn the crankshaft until you feel the piston (via the screwdriver) come all the way to the top of the piston bore. At the same time, watch the timing marks on the crankshaft. The engine is on top dead center when the mark on the crankshaft pulley lines up with the mark on the 5 o'clock position on the block, next to the crankshaft pulley. If the marks line up, but the piston is not all the way to the top of the bore, turn the crankshaft once more and everything will line up. 4. Step 4 Remove the crankshaft pulley bolt and the crankshaft pulley, using the appropriate sockets. Make sure the crankshaft does not turn while you are removing the pulley. If it does, repeat Step 3. Remove the lower timing belt cover. 5. Step 5 Loosen the bolts on the left and right engine mounts. Do not remove the bolts--they need only to be loosened enough so that the engine can move a little bit. Unbolt the radiator overflow tank, but do not disconnect the hoses. Lay the overflow tank out of the way. Disconnect the cruise control cable with the appropriate socket or wrench. The cruise control cable is located on the throttle. 6. Step 6 Support the engine by placing the 2-by-4-inch board on the floor jack. Slide the floor jack under the engine and jack it up until it contacts the bottom of the engine. Remove the front engine mount, using the appropriate socket. 7. Step 7 Remove the power steering pipe bracket, the upper timing belt cover and the front engine mount bracket, using the appropriate sockets. Disconnect the accelerator cable and the cruise control cable from the valve cover. Remove the valve cover. 8. Step 8 Slide the camshaft alignment tool into the slots at the rear of the camshafts. Loosen the tensioner bolt, but do not remove it. Turn the tensioner clockwise with the appropriate-size Allen wrench, releasing tension on the belt. Unscrew the tensioner retaining bolt four turns. Unhook the tensioner bracket from the metal clip behind the tensioner. 9. Step 9 Remove the plug from the center of the exhaust side camshaft (the right camshaft when you are looking down at the engine) by unscrewing it. Using the appropriate wrench, hold the camshaft by putting the wrench on the hexagon-shaped end of the camshaft where you removed the plug. Loosen the retaining bolts on both camshaft sprockets. Remove the timing belt. Check the valve on the number 4 cylinder. The camshaft lobe should be facing inward. 10. Step 10 Install the crankshaft pulley, making sure the notch and the pointer are lined up. Remove the plug from the engine block, next to the motor mount bracket. Install the crankshaft timing pin. Adjust the crankshaft until it rests against the timing pin. Make sure all the timing marks stay lined up. Remove the crankshaft pulley. 11. Step 11 Install the new timing belt around the crankshaft sprocket, working your way counterclockwise, keeping the timing belt tight on the side opposite the tensioner. The timing belt route goes on the inside of the two idler pulleys, then around the outside of the camshafts and the inside of the tensioner. Check to be sure the crankshaft is still pushed up against the timing pin. Hook the tensioner bracket on the metal clip. 12. Step 12 Turn the tensioner counterclockwise with the appropriate-size Allen wrench, until the pointer is lined up with the mark located halfway between the 12 o'clock and 1 o'clock position. Tighten the tensioner bolt to 18.5 ft-lbs. of torque, then remove the Allen wrench. 13. Step 13 Hold the camshaft by putting a wrench on the hexagon part of the shaft. Tighten the intake sprocket retaining bolt to 50 ft-lbs. of torque. Tighten the exhaust sprocket retaining bolt to 44 ft-lbs. of torque. Remove the crankshaft timing pin and the camshaft alignment tools. 14. Step 14 Hold the exhaust camshaft by placing a wrench on the hexagon part of the camshaft. Torque the exhaust sprocket retaining bolt to 89 ft-lbs. of torque. Turn the crankshaft almost two turns (slowly). Reinstall the crankshaft timing pin. Turn the crankshaft clockwise until it touches the timing pin. Reinstall the camshaft tool in the camshaft slots to make sure it slides in smoothly. If it doesn't, remove the belt and repeat the procedure. 15. Step 15 Remove the camshaft tool and the crankshaft timing pin. Install a new plug into the exhaust camshaft sprocket and torque the plug to 27 ft-lbs. of torque. Install the plug into the crankshaft timing pin hole and tighten it to 18.5 ft-lbs. of torque. Install the rest of the parts in reverse order of removal. Tighten the crankshaft pulley bolt to 85 ft-lbs. of torque.
How do you change the crankshaft seal in a 1999 dodge caravan?
You have to remove the drivebelt accessories and then remove the timing covers and take out the timing belt or chain. Basically you have to tear the side of the engine apart to get it out. It's a good day or two of work.
Where is the timing mark on a 1994 Caravan 2.5L 4-cylinder?
the way it looks in the chilton manual, the timing marks are on the crankshaft and the intermediate shaft sprockets. If anything else is found, it will be posted. hope this is of some help to you for now.
How do you check the timing on a 1991 straight 6 ford F-150?
Connect timing light to battery and No. 1 cylinder and aim light at crankshaft Connect timing light to battery and No. 1 cylinder and aim light at crankshaft timing marks
Does a 2005 dodge caravan 4-cylinder have a timing belt or chain?
The 2.4L has a timing belt.
What is the timing mark for a 1965 Chevy 6-cylinder 194?
Crankshaft
Does a Grand Caravan have a timing belt?
No . It uses a timing chain. you can see a diagram of it in the repair information at "AutoZone's" website. The Caravan's with the 4 cylinder engine do use a timing belt.
How do you replace front seal in 1996 Dodge Grand Caravan has 3-0 engine?
You have to remove the serpentine belt and drivebelt accessories then the passenger side engine mount, remove the timing cover, remove the timing belt, and the crankshaft sprocket to access the seal. It's about a day and a half of work.
How to remove timing cover 82 Honda?
Remove 1 Auxiliary Drive Belts. 2 LH top engine mounting. 3 Crankshaft Pulley 4 Cylinder head cover 5 Timing belt upper cover 6 Timing belt lower cover
How do you install 2000 galant timing belt?
Remove the drive belts, crankshaft pulley, and timing covers. Align the timing marks on the camshaft and crankshaft and r+r the belt
Is a timing belt and serpentine belt the same on a 1997 Dodge Caravan?
No. The timing belt or chain connects to crankshaft and camshafts. The serpentine belt connects the crankshaft with the alternator, ac compressor, power steering, etc.
How do you remove timing gear on 94 dodge 2.5?
There is a special tool ( a puller ) to remove the crankshaft sprocket.There is a special tool ( a puller ) to remove the crankshaft sprocket.
Does a 2010 dodge caravan 6 cylinder have a timing belt?
The 4.0 L has a timing belt. All other engines have a timing chain.
