Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.
it may not be grounded. correctly. did you check it before you put it on? check with volt meter see if it is getting power. also it maybe that the rod to the wipers are jammed check them out.
The type of fluid required is written on the dipstick.
First You Have To Check The S Terminal On The Starter Or Solenoid To See If Is 12 Volts When You Turn The Switch Into A Runn Position If You Have 12 Volts Then You need To Replace The Starter Motor You Need To Go Under The Truck You Well See The Starter Right Ther Is Realy Symple To Replace Two Or Three Bolts & Two Cables All Depends If Is A V6 Or V8
pop the hood and look directly at the motor in front of the radiator and start and the front of the motor on the passenger side it goes 1 2 3 4 and on the front of the driver side goes 5 6 7 8
check vaccuum hose for blockage . also check egr valve if both are good, replace vaccuum booster
To replace a windshield wiper motor for a 1998 F150, first remove the bottom trim on the window. Then remove both wiper blade assemblies and all screws on the metal cowling. Remove the retaining clip from the wiper motor linkage and pull the controls rods off.
First, remove the windshield wipers. Then you can remove the cowel just in front of the windshield. There are a bunch of screws connecting it to the firewall. Once you remove this, close the hood. Now everything is easily accessible and the rest is intuitive. Replace everything by using the opposite procedure.
around $150.00
end of drivers door there is a sticker, and at the bottom of the windshield, on the dashboard, it is viewable from outside the vehicle.
Yes, you can replace the oil pump in a 1978 F150 with 351 Winsor without lifting the motor. To replace the oil pump you will need the proper tools and supplies.
top of the fire wall under the hood your wiper arms will connect
it is located and accessible under the dash by the front passenger floor board. need 8mm nut driver only. easy
how do you replace the freeze plugs between the transmision and motor on a 1997 f150 5.4
hello. Here is a glass company called Conway Glass Plus....here is there number (501) 450-7587
If the windshield wipers are not working in a 1998 Ford F150, the cause could be a blown fuse. There could also be a problem with the vacuum hoses connected to the wiper motor or the wiper motor itself.
Take it to a Ford Dealer.
The governor for the wipers is located near the fuse box. It is wired to the harness going to the wiper switch.