0
How would you remove the door panel of a 1992 Integra to fix the lock?
Wiki User
∙ 19y ago
The question you ask is too involved for a proper answer. You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
Wiki User
∙ 19y ago
Add your answer:
Earn +20 pts
How do you remove the backdoor panel of a 1992 Mazda 929?
The 1993 mazda's back door is attached with clasps all around the door. To remove it, simply pry around the edges. At the bottom, there is a verticle clasp as opposed to the rest which go directly into the door. This clasp has a screw which must be removed. If trying to unscrew this screw is not making progress, it may be the case that it has been stripped or rusted (mine was both). After popping all of the rest of the clasps, the panel can be lifted off of the door frame, with this single clasp on the bottom still attached. Once the panel is removed and this clasp on the bottom is the only one remaining, it can be pushed out from above.
Where is the fuse for the brake lights for 1992 econoline van?
it is fuse number one in the interior fuse panel. it is a 15 amp fuse. should be located in the lower right corner of the fuse panel. the fuse panel itself is located under the left hand side of the instrument panel
How can you remove and replace a blower motor on a 1992 Lincoln Town Car without having to remove the antifreeze reservoir?
If the reservoir is blocking the way, then it will have to be removed.
How do you replace 91 previa sliding door outside handle?
This is copied from another site:QuestionThe exterior sliding door handle on my 1992 Toyota Previa broke so I bought a new one from the Toyota dealer. To install the handle, I have removed the interior door panel - almost. I can't figure out how to remove the interior door handle, which is preventing removal of the panel. Does this require a special tool? Any other tips for the project would be appreciated. Thanks.AnswerThe handle is held on with a spring clip, the easiest way to remove it is to insert a thin towel or rag behind the door handle and move it around until it catches the open end of the clip and then pull it out, to reinstall it put the clip on the door handle and just push it on to the splined shaft.ifthis unswer above it's wrong....if you remove the panel already look inside where the handle its located you will have to remove hte clips that's attach to the wires then take a number 10 rachet and remove the bolts that's hold the handle to the door install the newone and reverse the prosigues ...- - - - - - - - - - --Well, that is how you remove the inside handle but not the outside handle. After removing the inside handle, remove the small screw in the upper part of the sliding lock, then remove the inside panel which is held on with snap connectors. There are two bolts that are accessed via holes in the inside door wall. Loosen these bolts with a socket then remove them with a magnetic Phillips screwdriver so they do not fall into the bottom of the door.The handle is also connected to a cable which must be disconnected to remove the handle.Replacement handles are sold at previaparts.com, eBay, and Amazon. The handle at previaparts.com costs a little more but it also includes the cable.
How do you change the starter on a 1992 deville 4.9L?
It's quite a process that shouldn't be attempted without the factory service manual. Basically, you need to remove the intake manifold to get to the starter. After the intake is off, it's easy to do. But the factory service manual would have all the info you need to safely and correctly remove the intake without damaging any of the delicate fuel injection parts.
Where is the defrost relay located on a 1992 acura integra?
below the left side of the instrument panel behind the kick panel on the fuse box
How do you remove the door panel on a 1999 Cougar?
how to remove the door panel on a 1992 mercury cougar
Where is the computer located in a 1992 Nissan Maxima?
It is in the console, remove the panel where the passenger's left foot would be.
How do you replace the driver's side electric window switch on a 1992 Acura Integra?
The driver side electric window switch on a 1992 Acura Integra is reached by removing the door panel. Unbolt the switch from the mounting bracket and disconnect the wiring from the harness. Replace the unit.
Can a 1992 integra front bumper fit on 1991 integra?
yep
Does the windshield from an Acura Integra'96 fit an Acura Integra 1992?
no
What do you do to remove the 12 volt battery in a 1992 corvette?
Remove the lower panel from left fender .
Where is the ECU on a 1992 Nissan Maxima GXE?
On the console, remove the panel on the right side of the console where the passenger's left foot would be.
How do you remove 1992 Mercedes 300 SE rear door panel?
You can remove the rear door panel from your 1992 Mercedes 300 SE by removing the clips on the perimeter of the door skin. Once the clips are removed the door panel should come off.
How do you remove the radio from a 1992 Lexus SC400?
You have to remove the center dash panel to get access to the bolts, screws.
How to remove gauge cluster on a 1992 acura integra. I have removed center console and driver and pass. panels to get to additional screws. but won't pop off around ac panel. are there more screws?
why does my speedometer needle bounce, when I'm doin less than 80
What is the firing order for a 1992 Acura Integra LS?
The cylinder firing order for the 1992 Acura Integra is: 1-3-4-2
