0
Installed fuel pump on a 99 s10 by removing bed Now have no power to the grey wire at pump The old pump had power before removal Any suggestions?
I suggest you check for power at the harness. The relay will cut of power after about 4 to 5 seconds but should be enough to test the power there. I took a light bulb that has the wire prongs and insert one to the grey wire, and one to the black wire. When you turn the key it should light then turn off when the relay cuts off the power. If you do have power there, then the problem can be either the harness on the fuel pump or the harness connector on the fuel pump, (the one that has 4 prongs), You may interchange the old harness to check. Hope this helps. good luck. Frank
What else can I help you with?
Why do they put alcohol on glass before painting it?
Its a cleaning agent for the removal of greases & oils.
What was the last photograph Ansel Adams took before he died?
He was in bed, recovering from the removal of cancer from his leg. He died of a heart attack.
How much does laser tattoo removal cost?
Most laser tattoo removal is done by a dermatologist who more or less sizes up how much he can get you to pay and that's how much he's going to charge you. Updated Answer: Laser tattoo removal can become very expensive. Often as much as 10-20 successive treatments may be necessary to treat most tattoos. Also, laser light is not effective on all ink pigments and certain exotic hues, not to mention the health risks associated with laser tattoo removal. I suggest you read more about The Dangers of Laser Tattoo Removal at the link below before you consider such a procedure.
I'm having problems with ghosting on my Samsung 32 inch TV I tried many things to fix it but nothing seems to work though I think it might be bad outlets had this problem before Any suggestions?
I am not sure why the ghosting is not working in your Samsung 32 inch TV. I have not has a problem with this before.
When painting what is involve in surface preparation?
It's like pre-treatment for removing scale, dirt, or else from a surface before you do a coating work on it. It's often called blasting.
What variable should be measured when removing oil form sand?
The variable to measure when removing oil from sand is the oil concentration remaining in the sand after the removal process. This can be quantified by analyzing the oil content in the sand before and after the removal process to assess the efficiency of the oil-removal method.
Why must the engine be set at TDC before removing the distributor?
Because the replacement distributor and spark plugs wont fire correctly if it installed in any other position.
How do you change brake pads on a 1997 Toyota Celica?
Brake pads on a 1997 Toyota Celica are changed by removing the wheels, unbolting the calipers, and removing the old pads from the calipers. The caliper piston must be pushed in before the new pads can be installed.
What is the purpose of a replace receptacle and how can it be installed in a home?
A replacement receptacle is used to provide a safe and functional electrical outlet in a home. It can be installed by turning off the power to the outlet, removing the old receptacle, connecting the wires to the new receptacle, and securing it in place before turning the power back on.
How long to wait before using pill after Mirena removal?
It makes sense to start just before the removal.
Why is it a good idea to temporarily disable a malicious process before removing it altogether?
Temporarily disabling a malicious process can prevent it from causing further harm, giving you time to investigate and ensure that its removal won't disrupt critical system operations. It can also help in identifying any dependencies or connections the process has with other systems or processes before completely removing it.
How do you replace brake rotors on a 2003 Chevrolet Cavalier?
Real easy. After removing the brake caliper, tap, if needed, the rotor loose from behind. By the way, I found out today the caliper cyclinders can be squeezed with a C clamp before the removal. This eases the whole process of the removing and reinstalling new pads.
Why is it good idea to temporarily disable a program before removing it?
Because - if the program is still running, there will be 'residues' in the computer's memory and hard-drive. Terminating the program clears the program from the cache - to allow for more thorough removal.
What are some suggestions on how to keep your mouth shut?
Think before you speak.
How do you completely access the transmission filter with removal of the transmission pan on a 2003 Nissan altima?
The screen is accessable by removing the bottom pan of the transmission. most people clean it with carb cleaner or brake cleaner and dry it before reinstalling it.
Why is it a good idea to temporarily disable a program before removing it altogether?
Because - if the program is still running, there will be 'residues' in the computer's memory and hard-drive. Terminating the program clears the program from the cache - to allow for more thorough removal.
Should the ram be installed before the CPU?
Since the computer won't work without both of them installed it doesn't matter which is installed first.
