Yes, there is a huge difference. If you use a valve thread for an adapter instead of valve outlet, you'll be in a world of hurt. That's because the adapters have the correct threads! If you use the outlet, you might cross-thread and you don't want to do that. If you turn around twice hopping on one foot and clap your hands twice, it should be ok. But that's only if you spit on the valve outlet before you thread in the new valve adapter.
The preceding is a JOKE. Please post intelligently to get intelligent replies.
I don't know if you're talking about a CAR or a WASHING MACHINE or a SPACE SHUTTLE.
Answer 2Actually, a valve adapter should connect directly to a valve thread, that is what the adapter is for. Usually, the valve outlet connects directly, but if you don't have a plug you need the adapter to connect two outlets together. Of course, you really should just use the assembly properly with the plug end connecting to the outlet.It really depends on what color chart you are comparing, (Paints, embroidery thread) but in general a coral has more yellow/orange/pink component and claret has more violet/blue
No , embroidery thread comes in single strands of various sizes and are sold wrapped around spools similar to sewing thread. Most Embroidery threads are smooth, tight made to be used with machines. Floss is two to six strands loosely twisted , and are sold in hanks when a hank is wrapped in a loose coil then it is called a Skein. (some two strand flosses are sold in spools) the main difference between a strand of thread and a strand of floss is the tightness of the twisting which adds strength. a single strand of thread is harder, firmer to the touch a single floss softer in sewing a single strand of cotton floss will often break where a similar cotton embroidery thread will not.
normal thread is used, the thread used in Tailor work. It is just the way they use it, it seems magic.
You thread a needle with the thread you want to pull through, pass the needle into the material slightly within the margins of the pattern and pull the thread through. You don't really have to pull the top thread through to tie off because the stitch density is high enough to lock the thread, you can clip close. If you feel the need, unpick a few stitches (don't rip them, unravel the top and bobbin threads) until you have enough length to work with, pull the top thread through the fabric with the bobbin thread ad tie them together. When you change top thread, lay a short tail of the previous color and the new thread across the next pattern section and the thread will be locked. Same idea when you change the bobbin thread
The thread must come from the FRONT of the upright spool on the back of the machine. Thread through the small eyelet on the back (nearest the spool(s), projecting from the top), then through the thread guide at the front of the machine. If you are using a double needle (therefore two spools of thread), the thread from the left-hand spool should go through the top hole and the thread from the right-hand spool through the bottom hole. Come down to the tension disks. Bring the thread through the back disk, up again under the wire guide, and down under the thread guide that is just to the left of the tension disks. Bring the thread through the eye of the take-up lever (the piece that moves up and down when you sew) from RIGHT to LEFT. Guide the thread back down through the thread guide next to the tensioner. There is a little thread guide just inside the door on the left side of the machine; bring the thread through this guide. Then pull the thread through the wire guide above the needle (it's easiest to hold the thread horizontally to do this). Thread the needle front to back. HTH. YMMV.
A virus runs in a thread, as do all programs. The difference between a generic thread and a virus is that the thread may not be harmful, while the virus generally is.
In computing terms - A 'thread' is a topic of discussion, and a 'post' is a response to the 'thread'.
The difference between thread rope and string is that thread is more thicker than string and that string is more thinner than rope and thread is more thinner than rope there's your answer geese
No.
The difference between thread rope and string is that thread is more thicker than string and that string is more thinner than rope and thread is more thinner than rope there's your answer geese
Stop threading terminates the thread and cannot be resumed whereas suspend puts thread to sleep indefinitely and it can be resumed.
Basically no difference, except that process can use many threads; thread can use only one.
difference b/w thread based and use based testing
The difference between internal flush and full hole thread is that the roots of the full-hole tool joints are rounded, and the roots for the internal-flush joints are flat.
A thread is a sub process in other words one process can contain multiple threads.
The same metaphor: the difference of a person (thread) and a family (process) A process has at least 1 thread and may have many threads, while 1 thread must live within a process
They are both the same thread. They are both calling out a British Parallel Pipe thread. Please do not assume that this is the same as the standard North American pipe thread, as it is not close to the same.