0
What else can I help you with?
How about if it doesnt make any noise when you try to started but the batterie is find?
No noise when you try to start the vehicle usually indicates a dead battery, or a loose or disconnected cable/wire at the starter, solenoid (starter relay switch), or ignition switch.
What would cause a speedometer to start bouncing at 20 -25 mph?
the LACK of LUBE or Graphte on the speed0 cable IF it's not an electric sending unit type. The speedo cable spins inside another cable. Moisture will cause rust after a few years and this will cause the speedo cable to start to drag and release. If you remove the cable from the back of the instrument cluster and squirt in some graphite, this should help with the bouncing.
You tried to start your car all of the lights came on but it clicked andwhen you tried to start again it cranked what could this be?
I would suspect a loose or corroded battery cable. Remove the negative - cable first and clean both cable connection and the battery posts. Hook the positive + cable back up first. Can also be a starter solenoid going bad.
How do you tell your alternator is going out on your 96 Nissan Maxima?
You can take it down to a shop and get it tested, but if you can not afford that, you can take the negative battery cable off of the battery while the vehicle is running. If the vehicle dies, you may have a bad alternator.
Can you jump start a motor bike from a car?
Yes, just be careful what the cable ends touch.
What is a cable booster used for?
A cable booster also known as a jumper cable is used to connect with a discharged battery to a power source to jump start the vehicle. This is used when your vehicle can't start up.
Why do you have to do gas test before welding start on a pipe line?
So it doesn't explode.
How do you start a welding school?
how do I start a private welding school in Ohio
How do you start a private welding school?
how do I start a private welding school in Ohio
Why won't my car won't start the light won't turn on even when you jump start it what could be wrong?
Be sure and check the Negative battery cable connections where it connects to the frame or engine block of your vehicle. I have had this problem before and the cable was loose at the engine block. Also the Positive cable could be shorted to ground and jumping will not help.
How do you change the shifter cable on a 1993 Plymouth sundance with a manual transmission?
To change the shifter cable on a 1993 Plymouth Sundance with a manual transmission, start by safely lifting the vehicle and securing it on jack stands. Disconnect the old shifter cable from the shifter assembly inside the vehicle and from the transmission linkage underneath. Install the new cable by reversing the disconnection process, ensuring it is properly routed and secured. Finally, test the shifter to ensure smooth operation before lowering the vehicle.
How do you change handbrake cable on 207?
To change the handbrake cable on a Peugeot 207, start by safely lifting the vehicle and removing the rear wheels for access. Disconnect the old cable from the handbrake lever inside the vehicle and from the rear brake assemblies. Install the new cable by threading it through the same route and securing it in place. Finally, adjust the tension of the handbrake to ensure proper functionality before reassembling and testing.
How do you replace handbrake cable on vw caddy?
To replace the handbrake cable on a VW Caddy, start by lifting the vehicle and removing the rear wheels. Detach the existing handbrake cable from the handbrake lever and the brake assembly at the rear wheels. Install the new cable by routing it through the same path, securing it to the handbrake lever and connecting it to the brake assemblies. Finally, adjust the tension of the new cable as necessary and check the handbrake functionality before lowering the vehicle.
How do you jump start a 1999 Buick Riviera?
To jump-start a 1999 Buick Riviera, you'll need jumper cables and another vehicle with a functioning battery. First, park the working vehicle close enough for the cables to reach both batteries. Connect the red cable to the positive terminal of the dead battery, then to the positive terminal of the good battery. Next, connect the black cable to the negative terminal of the good battery and attach the other end to a metal ground on the dead vehicle, then start the working vehicle and allow it to charge the dead battery for a few minutes before attempting to start the Riviera.
How do you replace Porsche 944 handbrake cable?
To replace the handbrake cable on a Porsche 944, start by lifting the vehicle and removing the rear wheels for access. Detach the old cable from the handbrake lever inside the cabin and the brake calipers at the rear. Install the new cable by connecting it to the handbrake lever first, then routing it underneath the car and attaching it to the brake calipers. Finally, ensure proper tension and adjustments are made before reinstalling the wheels and lowering the vehicle.
How can I safely use a ring jumper cable to jump-start a vehicle?
To safely use a ring jumper cable to jump-start a vehicle, first ensure both vehicles are turned off. Connect the positive () ring to the positive terminal of the dead battery and the negative (-) ring to a metal surface on the car with the charged battery. Start the working vehicle and let it run for a few minutes. Then try starting the dead vehicle. Disconnect the cables in reverse order once the dead vehicle starts.
Can you suggest you a website about welding?
You can start whth the American Welding Society. Just google AWS.
