Monochrome Display Adapter: NotesThis document describes the behaviour of IBM's original Monochrome Display Adapter and some compatible cards.
The MDA is a monochrome card and displays on a TTL monochrome monitor. The original IBM mono monitor has green phosphor, so that's the colour I'll use when describing its behaviour. MDA monitors also exist with amber and white phosphor.
An alternative acronym for this card is MDPA (Monochrome Display and Printer Adapter).
The character ROM contains not only a 14-row font for normal operation, but two 8x8 fonts (one with thin uprights, the other with thick ones). This is because the same ROM is used on CGA cards; the 8x8 fonts are not displayed by the MDA.
Note that the character ROM is a 9264, which has a different pinout from the normal 27xx chip range (2764, 27128 etc.). This USENET posting describes how to get a 2764 ROM to work in a 9264 socket (it refers to the 5150 PC motherboard, but the pinout is the same for the MDA and CGA cards). Because the pinout is the same, it's possible to read the character ROM from an MDA or CGA by plugging it into the spare ROM socket on a 5150 motherboard.
Output is from a DE9 socket. The pinout of this socket is:
There is a single jumper (J1). In normal use, this is left open. It is probably used for diagnostic testing; if it is closed:
This appears to be used to isolate some of the card's subsystems from each other, for testing.
Memory MapIn normal use, an MDA produces an 80x25 text screen. Each character is 9 pixels wide and 14 high, giving a 720x350 pixel resolution. Although the characters are 9 pixels wide, the bitmaps in the ROM are only 8 pixels. For characters C0h-DFh, the ninth pixel column is a duplicate of the eighth; for others, it's blank.The memory storage scheme is that two bytes of video RAM are used for each character (80*25*2 = 4000, neatly fitting in the 4k RAM on the card). The first byte is the character code, and the second gives the attribute.
Character codes match whatever the font ROM in use is. Normally this is 'codepage 437' - ASCII plus a collection of accented characters, line graphics and a few other characters.
The attribute bytes mostly behave like a bitmap:
but there are eight exceptions:
These addresses are partially decoded on a real MDA, so that any even- numbered address between 03B0h and 03B7h will get you the CRTC address register. But the official register to use is 03B4h.
This is a write-only register.
03B1h, 03B3h, 03B5h, 03B7h: CRTC register read/write.This gives access to the selected CRTC data register. Most CRTC registers are write only; some are read/write or read-only. As with the address register, this is partially decoded; so although the official address is port 03B5h, it also appears at the other odd-numbered addresses between 03B0h and 03B7h. 03B8h: Mode Control RegisterOn a genuine MDA, this is a write-only register. Four of its bits can be set, but only two are any use: Bit 5: 1 to enable blinking, 0 to disable it.If bit 5 is 1, characters with attribute bit 7 set will blink. If not, they will have high intensity background.
Bit 3: 1 to enable video output, 0 to disable it.If bit 3 is 0, screen output will not be shown. The usual use of this is if you're reprogramming the CRTC registers; disable video output beforehand and re-enable it after.
Bit 1: 1 for black and white.This bit has no meaning, since the MDA always outputs in monochrome. The value written to it is stored (in chip U58) but nothing else on the card pays any attention to it.
Bit 0: 1 for high resolution mode.For any sane purpose this bit must be set to 1. For details of what happens if it is set to zero, see High Resolution Mode.
Quite why the MDA implements bits 0 and 1 is not clear. Possibly IBM originally planned to make an expanded MDA that supported 40 columns and/or colour; or perhaps the CGA was designed first, and the MDA was based on the CGA design, including vestiges of the CGA's 40-column and colour support. See also colour MDA.
03BAh: Status RegisterThis is a read-only register. Only two bits of the value read from this port are defined:(On a real IBM MDA, bits 7-4 are always 1, and bits 2-1 are always 0).
High Resolution ModeAccording to IBM's technical manual (page 1-128), setting bit 0 of port 03B8h to 1 puts the MDA into "high-resolution mode". One might therefore deduce that setting it to 0 selects a "low-resolution mode". This is not the case.Page 1-125 of the same manual warns:To ensure proper initialization, the first command issued to the attachment must be to send to CRT control port 1 (hex 3B8), a hex 01, to set the high-resolution mode. If this bit is not set, then the processor access to the monochrome adapter must never occur. If the high-resolution bit is not set, the processor will stop running.
That is, if you take an MDA out of high-resolution mode, then any attempt to access its ports or memory could well cause the computer to hang.
If a zero is written to bit 0 of port 03B8h, the following MDA functions change:
From top to bottom, the four solder pads beside the clock crystal (in the middle of this picture) are:
This suggests that the intention was to have a 4-pin header on these pads for a second clock crystal (or other timing source) to be connected - or, possibly, to replace the existing crystal with one that could provide two different clock signals. This would then have provided a suitable pixel clock for a low-resolution text display.
The printer portThe printer port on a genuine IBM MDA behaves as follows:I have no further information on this subject.
MDA ClonesUp to this point, I've concentrated on the genuine IBM MDA. This section gives a brief tour of how various MDA clones and supersets behave. General notesThe "high resolution" bit (bit 0) of port 3B8h is nearly always ignored, and most cards work fine with it set to zero.The undefined bits of port 3BAh may not be the same combination of zeroes and ones that they are on a real MDA; they may be all zeroes, for example. For Hercules-compatible cards (which are a superset of MDA), bit 7 is a vertical sync signal (1 when the screen is being drawn, 0 in the vertical blanking interval) and bit 1 returns lightpen status.
On a real MDA, the memory between B1000h and B7FFFh is filled with copies of B0000h - B0FFFh. Some clones (particularly Hercules cards) actually have 32k of RAM; others emulate the behaviour of a real MDA. I haven't yet seen an MDA clone that doesn't have anything between B1000h and B7FFFh, but that doesn't mean there isn't one.
Some MDA clones don't support dark and/or bright colours; they end up restricted to just normal, or normal plus bright.
3270 PCThe 3270 PC's video card supports programs which treat it as an MDA - either on its own colour monitor, or on a mono monitor. The resolution is the same as a normal MDA (720x350) but the font used is based on the 3270 terminal rather than the original MDA.On a mono monitor, the attributes displayed are not quite the same as on a real MDA:
On a mono monitor, only one bit in the MDA mode control register has any effect - bit 5 (enable/disable blink). The others are ignored.
The video RAM repeats at 4k intervals all the way from 0B0000h to 0BFFFFh.
On a colour monitor, the attributes in MDA mode act as colours (bits 0-2=foreground, bits 4-6=background, bit 7=blink).
The extra video mode 30h (720x350 graphics) can be used on an MDA monitor. So can the 3270 emulation features.
Amstrad PPC / PC20The Amstrad PPC has a chipset that can emulate MDA or CGA - either driving a normal monitor, or its internal LCD. The desktop version (PC20 aka Sinclair PC200) uses a similar system, but only supports an external monitor.One card I have encountered, which appears to be a Hercules clone of Eastern European origin, has a further capability - two ROM fonts, selectable in software. These options are controlled in a similar manner to other extended features in the Hercules: Bit 2 of port 3BFh must be set to enable the feature, and then Bit 4 of port 3B8h selects which font to use. The card ID in bits 6-4 of port 03BAh has all three bits set.
Depending on the graphics card in your computer it will state the graphics you have
what is meta graphics?
Vector graphics refers to a type of graphics that stores color information as well as the paths (curves and shapes) rather than using pixels to store image information (raster graphics). This means that it will retain image quality better than raster graphics, no matter how you scale it (enlarge or shrink) when it comes to designing logos, line art, and other 2D imagery. The most common file type for vector graphics is Scalable Vector Graphics (SVG). In programming, a vector is a scalable array (a type of array that can be resized). For example, strings in C++ would be a vector of characters/bytes.
Motion graphics is the term used for all types of graphic movements, including 3D elements, cell animation, stop motion animation, digital video, film, animated text, web-based animations, apps and many other types of motion graphics. The designer of these graphics provides information through the graphic while guiding the readers through a story in some way. Motion graphics aren't just used for Internet but they can also be used in TV and film. Motion Graphics, as a composed word, means Graphics in Movement.
Rastor graphics are also called Bitmap graphics, and are generally used with better results in photography. The pixillated form of Rastor graphics is more beneficial to subtle shading as opposed to the straight sharp lines of the Vector graphics.
Graphics just means images.
you can get MDA at any age!
1) (Monochrome Display Adapter) The first IBM PC monochrome video display standard for text. Due to its lack of graphics, MDA cards were often replaced with Hercules cards, which provided both text and graphics. (2)(Modular Digital Architecture) An earlier snap-together, building-block approach for adding peripherals to a PC from NeoSystems, Inc. (3) (Mechanical Design Automation) Refers to applications that help automate the design and engineering processes from concept to manufacturing. Automotive, aerospace and discrete manufacturing are examples of industries that use MDA.
in graphics gdriver means graphics driver. it contains DETECT as an exception.
A graphics card plugs into your computer, integrated means the graphics chip is ready installed on the motherboard.
graphics means chithram in Malayalam in genaral...but if you mention computer graphics....it is said as computer graphics itself.
bgi in computer graphics means "borland graphics interface", these r the files which contains information about all the graphics funtion.
MDA Space Missions was created in 1999.
mda is the drug. Methylenedioxymethamphetamine, makes your serotonin levels high
Most graphics cards in laptops are integrated graphics, which means that the motherboard handles the graphics processing and which also means it isn't upgradeable or replaceable. Consult your instruction manual to see if your laptop is one of those that supports upgrades, and how this can be achieved.
MDA Labor Day Telethon was created in 1966.
MDA - TV series - ended on 2005-09-22.