0
What is the maximum number of 60-W light bulbs you can connect in parallel in a 120-V home circuit without tripping the 30-A circuit breaker?
If your not interested in safety or wiring codes use the formula. E x I = Va(Watts without knowing Power Factor.) E is your voltage at the source (Breaker) 110v, 115v, 117v. I is 15amp the breaker is rated for.
X is your number of bulbs.
example. 110 x 15 = 60X : 60x = 1650 : 1650/60 = X Please do not attempt doing this hookup. % If your not interested in safety or wiring codes use the formula. E x I = Va(Watts without knowing Power Factor.) E is your voltage at the source (Breaker) 110v, 115v, 117v. I is 15amp the breaker is rated for.
X is your number of bulbs.
example. 110 x 15 = 60X : 60x = 1650 : 1650/60 = X Please do not attempt doing this hookup.
What else can I help you with?
What is the main difference between a series circuit and a parallel circuit?
The series circuit has one wire, while the parallel circuit has two wires. And if you connect the extra wire its dim because your taking away electrons and energy flowing through the main circuit -Hope this helped:D The difference is that series circuit has one path but parallel has more than one path. -hope this helped!:D ~Bunnii Boo
How can light bulbs be switched on separately in a circuit?
Arrange the light bulbs in parallel with a swith between them. Like in the (simple) diagram below _____________/ ____________ | | | | | | | | | | | | _ O O - | | | | | | | | ------------------------------------------ I hope this helps :-) ---- Visualize two parallel lines like a ladder. One is the "hot" line and the other is the neutral. Now visualize the cross rungs in the ladder. These will be the loads on the circuit. Go from the "hot side of the ladder through a switch and through a light bulb to the neutral side of the ladder. Go up one rung on the ladder and add another switch and light bulb. Go up one more rung and connect a receptacle from the "hot" side of the ladder to the neutral side of the ladder. This is how house circuits are wired on each breaker circuit. This circuit could be for one room only. Another circuit could be wired for another room , and so on. As you can visualize turning the light off and on does not effect any of the other devices connected to the same circuit.
Why do lights in a parallel circuit burn brighter than in a series circuit?
In a parallel circuit, more power is provided to the lights. Power = V2/R . The resultant resistance of the circuit is lower, and the potential difference is not divided as in a circuit in series. Thus, lights in parallel burn brighter.Additional InformationA lamp's power rating only applies at its rated voltage. Because the voltage across each branch of a parallel circuit is the same, each lamp can be supplied with its rated voltage and, therefore, will operate its rated power. In a series circuit, the voltage appearing across each lamp will be considerably lower and, so, the lamps will not operate at their rated powers.
What if your friend says that when jump-starting a dead battery you should connect your live battery in parallel with the dead battery to replace the dead one do you agree?
That is correct, but using the term parallel is an overly confusing way of saying it. - You should connect positive to positive and negative to negative. This will retain voltage and increase capacity. If you confuse the term 'parallel' with 'serial' and connect them positive to negative and negative to positive, you'd double the voltage and probably kill most if not all of the electronics in both cars.
What could you do to a closed circuit consisting of 2 batteries and 2 light bulbs and a switch too increase the current?
The switch will not increase the current. The only thing that will increase the current is adding a larger load.Another AnswerTo maximize current flow in a circuit with 2 Flashlightbatteries, 2 Flashlight bulbs, and a switch, set aside the bulbs, put the batteries in series, connect the switch between the end poles of the battery set, and close the switch. The batteries will get hot and probably leak electrolyte, and be drained in seconds.If you want to maximize current through the circuit withthe bulbs in it, connect the bulbs in parallel to each other, and in series with the switch.
What is the maximum number of 100-W bulbs you can connwct in parallel in a 120-V home circuit without tripping the 20-A breaker?
You can connect a maximum of 24 100-W bulbs in parallel on a 120-V home circuit without tripping the 20-A breaker. This is calculated by dividing the total circuit wattage (2400 W) by the wattage of each bulb (100 W) to find the number of bulbs that can be safely connected.
Can I add a circuit breaker wired in parrell to a current breaker to reduce the load on the breaker?
No, add new breaker,find a junction box and split the series, or add a box and split the load. You only need to do this if the breaker is tripping from overload. 12ga wire should have a 20amp breaker not a 15amp. If I understand your question,wired in parallel, this would be one hot connected to two breakers, first off two breakers is 220v not 120v , and 220v has two hot wires. Never connect two breakers together on one line.
How would you connect solar panels to a circuit breaker?
To connect solar panels to a circuit breaker, you would typically connect the output of the solar panels to a solar charge controller which then connects to the circuit breaker. The circuit breaker acts as a disconnect switch to isolate the solar panels from the rest of the system for safety and maintenance purposes. It is important to follow all electrical codes and regulations when connecting solar panels to a circuit breaker.
How can I wire multiple outlets and lights on the same circuit?
To wire multiple outlets and lights on the same circuit, you can connect them in parallel using a junction box. Run a main wire from the circuit breaker to the first outlet, then connect additional outlets and lights in parallel to the first one. Make sure to follow local electrical codes and use proper wiring techniques to ensure safety.
Where do you connect the white wire from the shunt breaker?
Connect to the circuit neutral wire which should also be white.
How is a circuit breaker panel wired?
how to connect cables to switches 240 box
Can you use 2 20amp circuit breakers to protect to 40amp?
No, it is not safe to use two 20 amp circuit breakers to protect a 40 amp circuit. Circuit breakers are designed to protect the wiring in a circuit from overheating, and using a higher amperage circuit breaker than the wiring is rated for can lead to overheating and potential fire hazards. It is important to use the correct size circuit breaker for the amperage rating of the circuit.
How do you connect resistor?
In a circuit, either in Parallel or in Series with other components.
How do you put bulbs into a circuit without dimming themg them?
You connect them in parallel.
How to wire a circuit breaker properly?
To wire a circuit breaker properly, first turn off the power to the circuit. Then, connect the hot wire to the breaker terminal and the neutral wire to the neutral bus bar. Finally, connect the ground wire to the ground bus bar. Make sure all connections are secure and the breaker is properly seated in the panel before turning the power back on.
How can I add a circuit breaker to my electrical system?
To add a circuit breaker to your electrical system, follow these steps: Turn off the main power supply to your home. Identify the circuit where you want to add the breaker. Install the new circuit breaker in the breaker panel by attaching it to an available slot. Connect the wires from the new circuit to the breaker. Turn the main power supply back on and test the new circuit breaker to ensure it is working properly. It is recommended to consult a licensed electrician for assistance to ensure safety and compliance with electrical codes.
How to install a GFCI breaker in a circuit?
To install a GFCI breaker in a circuit, first turn off the power to the circuit at the main electrical panel. Remove the panel cover and locate the circuit breaker that needs to be replaced with the GFCI breaker. Disconnect the wires from the existing breaker and connect them to the new GFCI breaker according to the manufacturer's instructions. Secure the GFCI breaker in place and replace the panel cover. Turn the power back on and test the GFCI breaker to ensure it is working properly.
