0
What else can I help you with?
Can Microlam wood be used for outside decks in New York State?
MIcrolam is very similar to lumber, but it is much stronger. it is made with the same layering technique, but has more durablilty, and requres less supporting beams. Microlam would be a great choice for a deck. MIcrolam is very similar to lumber, but it is much stronger. it is made with the same layering technique, but has more durablilty, and requres less supporting beams. Microlam would be a great choice for a deck.
How far does a car headlight reach?
A standard low beam car headlight will shine a maximum of 350 feet. While high beam headlights will reach approximately 450 feet.
Effective length of a beam?
the efffective length of a beam is the length along the beam at which the beam will fail when a load is acting upon it. This effective length is usually near the centre of the beam as that is where the stresses are the greatest. For example a fat chick jumping up and down on the beam would reduce the effective length dramatically as the loads are semi-constant but ginormous.
Triple-beam balance definition?
A triple beam balance is a scale used to measuremass.
What is a flush beam?
A flush beam is a beam that is flush the the surrounding floor or ceiling joists. Often held in place with metal connectors. It could be a steel 'I' beam, lvl, built up wood. It is used when ceiling height is needed to be maintained.
How much weight will a microlam beam hold up?
The weight capacity of a microlam beam depends on its size, span length, and load distribution. It is important to consult a structural engineer to determine the specific weight capacity for your particular application.
Can holes be drilled in a Microlam beam that is 25' long x 3 thick X 16 high?
As a roof truss/I-joist/beam designer, I can tell you that you should not cut ANY holes in a microlam beam without consulting an I-joist/beam designer first. Microlam beams are not calculated to have holes cut in them. This requires special engineering.Depending on the size of the hole and it's placement, and the load that the beam is carrying you may not be able to cut a hole in it at all. Considering the 25' length (if this is a clear-spanning beam) I can warn you that abeam designer is probably going to tell you to find a different solution for this issue.Hope this helps!
What is the maximum span for a 9 12 microlam used as a floor joist on 16 inch centers?
unless you got a great deal on them, it would never make $$$ sense to use a microlam in lieu of a TJI joist or dimensional lumber. . .microlam is too costly if you have them on hand, I would call the manufacturer. . .they should be able to give you the numbers or send you a book with the span charts
Can Microlam wood be used for outside decks in New York State?
MIcrolam is very similar to lumber, but it is much stronger. it is made with the same layering technique, but has more durablilty, and requres less supporting beams. Microlam would be a great choice for a deck. MIcrolam is very similar to lumber, but it is much stronger. it is made with the same layering technique, but has more durablilty, and requres less supporting beams. Microlam would be a great choice for a deck.
What is the most accurate method to determine the maximum allowable span for a beam using a lvl beam span calculator?
The most accurate method to determine the maximum allowable span for a beam using a LVL beam span calculator is to input the specific details of the beam, such as the type of wood, dimensions, and load requirements, into the calculator. This will provide a precise calculation of the maximum span the beam can safely support.
What is the maximum weight capacity of the lvl support beam?
The maximum weight capacity of the lvl support beam is typically around 14,000 to 18,000 pounds.
What is the maximum weight capacity that the ceiling support beam can hold in this room?
The maximum weight capacity that the ceiling support beam can hold in this room is 500 pounds.
What is common about the location of the maximum moment along the beam in each loading case?
It is the center of the beam, if the beam is supported at both ends.
Which section of a beam must take a load to provide maximum strength?
the part of beam which has maximum section modulus should take more load for more strength.
What is the maximum span for a 2x6 beam?
The maximum span for a 2x6 beam is typically around 10-15 feet, depending on the load it needs to support and the building codes in place.
What is the maximum torque that can be applied to a beam before it reaches its breaking point?
The maximum torque that can be applied to a beam before it reaches its breaking point is the point at which the beam can no longer withstand any additional twisting force. This is known as the breaking torque.
Maximum moment of resistance of beam?
Rm= 8Mp/L
