0
What is torque specs for 1994 4 liter ford explorer intake manifold?
Wiki User
∙ 15y ago
Form Haynes Repair Manual #36071 4.0 SOHC V6 engine: install the bolts and tighten them finger-tight. torque to 89 inch-lbs.starting with the center bolts and working toward the ends. 4.0 pushrod V6 engine: bolt/tightening pattern is: top 4 bolts = 3,5,7,2; bottom 4 bolts = 1,6,8,4. Install the bolts and tighten them finger-tight and torque in 4 steps according to the pattern mentioned: step 1: 36 in-lbs; step 2: 72 in-lbs; step 3: 120 in-lbs; step 4: 144 in-lbs. (it is a cross-type pattern starting with the outside corners and working toward the center. BOLT LOCATIONS FOR TIGHTENING SEQUENCE FOR 4.0 PUSHROD 6V: TOP BOLTS 3 5 7 2 INTAKE MANIFOLD BOTTOM BOLTS 1 6 8 4 Hope this diagram for pushrod engine intake manifold helps.
Wiki User
∙ 17y ago
Wiki User
∙ 15y agotorque specs axel not and wheel hub bolts
Add your answer:
Earn +20 pts
What is the head bolt torque specs for 2.9 ford v6?
In my 86-96 aerostar repair manual it says to use new bolts , tighten the bolts over a 3 step sequence to the torque required. Here is the sequence 5 1 3 7 6 4 2 8 Torque specs Step 1 44lbs step 2 tighten intake mainifold to 36 -72 in lbs step 3 59lbs step 4 tighten intake manifold to 72 to 132lbs in-lbs step 5 turn cylinder head bolts an additional 80 to 85 degrees step 5 complet intake mailfold torque steps 3 and 4 i copied it word for word
What is the cylinder head torque specs for a 1996 ford escort 1.9 liter?
The 1996 Ford Escort 1.9 liter engine cylinder head bolt torque specification is 120 pounds. The head bolts should be torqued in 40 pound intervals.
Where is the pcv valve located on a 3.8 liter 1989 Olds 98?
In the intake behind the throtle body.
Does 89 Ranger 2.3 Liter have a PCV valve and where on earth is it?
Yes, the 1989 Ranger does have a PCV valve. I can speak for the 2.3 liter 4-cylinder version only. If you stand on the driver side of the engine compartment you will see the intake manifold (silver cast looking with the name FORD on it), on the bottom of the intake there is a 90 degree elbow (the intake forms a "Y" and if you look through the "Y" you can see the elbow) that points back toward the firewall. Connected to this is a rubber hose that routes back toward the firewall and then turns down at the firewall-side of the intake. If you follow this hose along you will come to the PCV valve. The valve is installed in the hose and connects to another rubber hose on the other side of the PCV valve. Hope this helps.
What is torque on the head bolts 2002 Cavalier 2.2?
The 2002 Cavalier 2.2 liter engine cylinder head bolt torque specification is 120 pounds. The cylinder head bolts should be torqued in 40 pound intervals.
Whats the torque specs for a 4.3 vortec intake manifold?
The torque specifications, for a 4.3 liter engine manifold, is 45 pounds per square inch. Torque the manifold bolts in 15 pound intervals.
What is the torque sequence for intake manifold on a 1997 mercury cougar 4.6liter?
The 1997 Mercury Cougar 4.6 liter engine intake manifold torque sequence should begin at each end of the manifold. Keep moving towards the center and alternating from and to end.
What is the torque for intake manifold bolts 1991 Buick le Sabre 3.8 liter?
what is the torque specificationfir the rockerarm bolt on 1991 Buick le Sabre v-6 3.8 liter
Intake manifold 4.6 liter 1997 Cadillac deville torque specifications?
the haynes book states 89 in pounds
What are the torque specs for a 2002 ford escape 3.0 liter engine intake manifold?
89 lbs. top & bottom
What are the torque specs on intake manifold bolts and exhaust manifold bolts for a 97 Chevrolet Cavalier 2 2 liter engine?
24 ft lbs lower intake 115 inch lbs exhaust
What are the torque specs on upper and lower intake manifold for a 2001 Pontiac grand am 3.4 liter?
lower intake is 115 in pounds upper is 18 ft pounds
What are the torque specs for a intake manifold on a 2001 Nissan Altima 2.4 Liter 4 cylinder?
12 to 14 ft. lbs in sequence
Where is EGR valve on 2000 Ford Explorer with 5.0 Liter engine?
back of the intake manifold, middleof the engine. lets gasses from exhaust back into the intake. will be a tube coming off it to the passenger side going to the exhaust manifold
Knock sensor location 05 5.3 liter Chevrolet silverado?
There is 2 of them and thay are under the intake manifold. You will have to remove intake manifold to get to them.
Where is the PCV valve located on a 2005 Mazda 6i with a 2.3 liter?
It is located under the Intake Manifold. You must remove the intake manifold to get to it.
How do i stop 5.7 liter intake gasket leak?
You will have to remove the intake manifold and install a new intake gasket. You have no choice.
