0
A drive belt causes the inside part of the generator rotate.
An electric generator can be either a magnet (and magnetic field) rotating and surrounded by wires or a coiled wire rotating in a surrounding magnetic field. EIther way works to generate electricity.
The wire is where the electricity is generated. We use more wire to generate more electricity and we coil the wires to keep the size from getting too big.
The stronger the magnet, the more electricity is generated. Instead of using a real permanent magnet, we usually make an electromagnet (such as wires wrapped around iron) attached to a battery or powered off the electricity created by the generator.
In an automobile it is not called a generator. It is called an alternator because it generates alternating current electricity instead of direct current.
What else can I help you with?
Why does your serpentine belt keep breaking?
it means you need a new belt...plain and simple....lots of people keep driving on their cars when a belt squeaks..and allit does is lead to other problems..... i am no expert, but i think it is the Drive belt that is squeaking
How do you replace the alternator on a 98 Chrysler Concorde?
There are three main steps behind replacing the alternator on the 1998 Chrysler Concorde. The first is disconnecting the battery cables for safety. Second, is depressing the belt tensioner to allow for the release of the drive belt. Finally the alternator can be unbolted from its bracket for replacement. If the drive belt, idler pulley and tensioner are worn it would be an ideal time to replace this components as part of the install.
Are tie rods part of drive axle?
No - they are part of the steering linkage.
What part of speech is the word drive?
The word driving is a verb. It is the present participle of the verb drive.
What are the adjectives in this sentence you took a coastal drive as part of your Pacific states vacation?
The adjectives are costal and Pacific states. Costal describes drive. Pacific states describes vacation.
How much to replace a generator belt on a 2003 volkswagen jetta?
A generator belt on a 2003 Volkswagen Jetta costs approximately fifteen dollars to replace for the part only. Labor pricing would increase the total cost.
When should one change a drive belt in a 1997 Buick Regal with 13K miles?
You should change the drive belt when you see cracking underneath the belt where it rides against the pulleys(the grove part of the belt)or you need to replace it when it continously squeals
Zu welchem fahrzeug gehöhrt GM Part Nr10085752?
To which vehicle does GM Part Nr 10085752 belong? Any small-block V8 Chevrolet. It is a drive belt and part of the Serpentine Accessory Belt Drive System (Part Nr 12497698. This deluxe serpentine belt drive system with air conditioner includes all the components to install on small-block Chevrolet engines. See the link below.
What size drive belt for cub cadet LT1050?
A-sect V belt 1/2 by 78 part # 954-0461
Toro GTS 6.5 horse mower drive belt part number?
115-4669
Where can you find tentioner of Buick Skylark?
The lower part of the drive belt runs around the tentioner. It's where the adjustment is made to tighten or loosen the belt.
How much does a serpentine belt replacement cost both part and service on a 2000 Mitsubishi?
You won't have a serpentine belt, Do you mean timing belt because in that case anywhere from 300-600$. If its the drive belts then about 14$ for each at your local part store.
How do you remove the alternator from a 2002 buick rendezvous?
OK this is the most complicated thing i have ever seen so ya might wanna take it to a shop this is in my rendezvous repair book good luck Generator Replacement Removal Procedure: -Remove the battery ground (negative) cable from the battery. -Rotate and secure the engine forward to access rear generator bolts. -Remove the generator B+ terminal nut. -Remove the generator B+ lead. -Remove the generator electrical connector. -Remove the drive belt from the generator. -Remove the generator front bolt. -Remove the generator rear bolts. -Remove the generator from the generator bracket and position the generator above the drive axle. -Remove the drive belt tensioner. -Remove the generator bracket. -Remove the power steering pipes from the power steering pipe retainer. -Remove the fuel pressure test port (schrader valve) cap from the fuel injector rail. "Important" Do not disconnect the power steering pipes from the power steering pump. -Remove the power steering pump and reposition the power steering pump in front of the timing chain cover in order to provide access for the generator. -Remove electrical harness from retainer on right fender well and position aside. -Remove the generator from the vehicle. Installation Procedure -Install the generator to the vehicle and position the generator above the drive axle. -Install electrical harness to retainer on right fender well. -Install the power steering pump to the engine. -Install the fuel pressure test port (schrader valve) cap to the fuel injector rail. -Install the power steering pipes from the power steering pipe retainer. -Install the generator bracket. Refer to Generator Bracket Replacement . -Install the drive belt tensioner.. -Install the generator to the generator bracket and position the generator above the drive axle. -Install the drive belt tensioner. -Install the generator to the generator bracket. -Install the generator front bolt. *Notice* Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. -Install the generator rear bolts. Tighten Tighten the generator bolts to 50 N�m (37 lb ft). -Install the drive belt. -Install the generator electrical connector. -Install the generator B+ lead. -Install the generator B+ terminal nut. Tighten -Tighten the generator B+ terminal nut to 13 N�m (115 lb in). -Rotate the engine rearward and install the engine mount strut bracket bolts -Install the battery ground (negative) cable to the battery. BBAASPENCER here in TN. This is how to roll it forward for access.Roll the engine forward is to take off the engine dog bones, put gear in neutral, attach a pulling strap to the engine and hoist and roll it until you gain access.
What are the three main components of a generator?
Drive shaft,Strong magnet,Coil of wire
What size is the belt for a power king 48 mower deck part 81-0094?
The drive belt for a 48" Power King Economy mower is 3/8" x 88" in a Gates Green Belt or equivalent high strength belt.
What do you call the part on a belt where the holes are?
belt loop. I've always referred to that part as the belt's tongue.
What part number is drive belt for 46 mtd 13ao771h055?
The drive belt part number for the MTD model 13AO771H055 (46-inch mower deck) is typically 754-04060A. However, it's always best to verify with the manufacturer's specifications or consult the owner's manual to ensure you have the correct part, as variations may exist depending on the specific model and year.
