Sorry, but you have a fairly big job ahead of you. You are going to have to sand (use fine grit sandpaper) and be sure you get both stains completely off. You can also go to your hardware store and ask if they have an solution to your problem. Good luck! MY 2 cents --- Before you start stripping all the finish off lets figure out what the white streaks and spots are from. If you have used a satin or flat finish poly on the cabinets without first applying a sealer coat the white streaks may be from the flatting agent in the polyurethane. If this is the case it can be fixed without stripping. To find out do a spot test by applying a gloss polyurethane over white streaks, if the white goes away the white spots and streaks are from the flattener in the poly you applied. Solution is to light sand cabs, apply a coat of gloss to the cabinets and let dry. The white streaks and spots should now be gone. Next light sand the cabinets and apply the satin or flat poly you used the first time and this time you will not have the white strips and spots. ___________
You just got some serious great advice. One thing you should check first though...make sure your poly and stains are compatible.
You don't. You will most likely have to restain after stripping.
Use a sealer if the drywall was damaged while removing the wallpaper, then use a high quality latex paint in the sheen of your choice.
if you have used a wax finishing agent on your subject piece, it might not be a good idea to use polyurethane over it. You probably should strip the wax coat as best as you can and then coat with poly. something tells me that since wax is an "organic base" material and urethane is synthetic, it might react with each other in a adverse way, or the poly won't adhere to the wood at all. Try contacting a builder's supply outfit and ask for specific information on this subject. Don't take a chance and ruin a good piece of wood. Good Luck!
It should reflect the cost of plastering PLUS 3-4 hours for removing and re-fitting toilet appliances.
removing too much water from aquifers can result in subsidence because the
You would use a vacume
You don't. You will most likely have to restain after stripping.
CLR (Calcium Lime Rust, a cleaning product) is good for removing rust and other deposits and effects from running water. In areas around the bathroom and kitchen where there is running water, it's excellent for removing things like that.
Refacing kitchen cabinets involves removing the doors and exposed edges of all cabinets. The parts that are exposed on the cabinets are now roughed up to be prepared for for edges and panels to be glued to them. The doors that were removed now get a new surface. This is in the form of a solid color veneer or a wood veneer. All removed cabinet doors are then put back to their original place, and the kitchen appears refreshed.
Sunset have a site online which offers many tips and step by step instuctions for refinishing kitchen cabinets. From removing hardware, priming, painting and drilling new holes to re-attaching the doors.
Scrubbing Bubbles Soap Scum Remover is great at removing soap scum from your glass shower doors.
Refacing kitchen cabinets is a labor-intensive project that can save you quite a bit of money, while increasing the value of your home. If you are not afraid of hard work, cabinet refacing is not that difficult. You start with removing all of the cabinet doors and drawers. Sanding comes next. Then you can repaint, stain, or put a veneer on the existing cabinets as they are on the wall. Then you apply the same finish to the doors and drawers. Add new hardware, if desired, and then put the doors and drawers back in your newly finished cabinets.
You would be better of removing the plywood floor completely - and tiling over the original surface.
This could be caused by your exhaust fan not properly removing moisture from your bathroom. It is always a good idea to use some X-14 (a mildew remover) every coupke of weeks when you start to see mildew. It is cause by lack of air flow in your bathroom, or a leak from upstairs. Is there is an upstairs bathroom? If so you might have a small leak somewhere in the supply or drain lines in the upstairs bathroom. If not a leak then possibly condensation is forming on a shower or tub above this bathroom.
Bleach and ammonia are both useful for removing mold and mildew of bath room. However, the two should never be used together.
if they are the same ones that came with your house - contact the real estate developer and try to track it down. also, some cabinet makers will tag all their products - BUT the tag might be very hard to find, look in every nook and cranny and especially at the back of the drawers, etc. It might even be on the back of the cabinets themselves and you wont see it without removing the cabinets from the wall. If they are the same as other houses in your development, go door to door and ask your neighbors, someone might know.
Yes why not. All cleaners are good for deep surface cleaning. Especially kitchen cleaners are very good in all respects. They are tough on stubborn stains and good for removing all. Bathroom don't get stains overnight, but yes over a period of time they do and need attention. If you have not yet tried using kitchen cleaners in bathroom, use once when you want to deep clean it.