For the front I believe a 15/16 socket will work. The rear I used a 7mm Allen wrench
How do I replace the heating coil in a 2006 Grand Caravan? I have no heat it only blows cold air.
The EGr valve can be difrent and is in difrent locations on the various engines
I just did my 2005 Ford Escape front brakes and the caliper was 7mm Allen and main holder is 18mm ...RRR Wis.'
Dry fill is about 9 quartsDry fill is about 9 quarts
The brakes on your 2005 Chevy Malibu require replacement every 25,000 to 35,000 miles, depending on how aggressively you brake the vehicle when driving it. Many people opt to have a repair facility change the brakes because they don't want to chance installing them incorrectly. However, because the rear brakes on the Malibu are disc breaks, the rotors are replaceable without fear of causing a safety issue. # step 1 Loosen the lug nuts that secure the rear tire to the wheel studs with a tire iron. Do not remove the lug nuts. # Step 2 Jack the rear of the vehicle off the ground and place a jack stand under each side of the axle. Lower the Malibu onto the jack stands. Place a wheel chuck in front of the front tire to secure the vehicle. # Step 3 Remove the lug nuts from the wheel studs and pull the rear tire off the vehicle. # Step 4 Remove the two bolts that secure the brake caliper to the axle housing assembly with a 7/16 socket. # Step 5 Pry the caliper off the rotor by wedging a large flat head screwdriver between the outside edge of the rotor and the inside edge of the caliper. Pull the handle of the screwdriver upward, using the side of the rotor for leverage. # Step 6 Tie the caliper to the rear spring with rope. Do not allow the caliper to hang down on the rubber hose--the hose could break. # Step 7 Locate the splined washer press fit onto one of the threaded wheel studs. Press a small flat head screwdriver into the spline and bend it outward. Pull the splined washer off the wheel stud with needle nose pliers. # Step 8 Slide the rotor off the wheel studs by pulling straight out on it. Due to rust, the rotor may stick to the studs. Tap on the back of the rotor with a rubber mallet to break it loose from the studs. Place the new rotor onto the wheel studs and slide a new splined washer onto the wheel stud. # Step 9 Open the hood of the Malibu and take the cap off the brake fluid master cylinder. It is located on the fire wall, driver side. # Step 10 Locate the brake actuator located behind the brake pad on the caliper. It is behind the backside brake. Place a pair of vise grips around the back of the caliper and on the brake pad and apply pressure to the actuator. Close the actuator approximately 1 inch to allow room for the new brake pads. # Step 11 Pull the old brake pads out of the caliper. They do not bolt on or attach with clips; they simply rest on tabs built into the caliper. Place the new brake pads into the caliper. # Step 12 Press the caliper onto the brake rotor and line up the bolt holes on the caliper with the bolt holes on the axle assembly. Bolt the caliper into place with the 7/16 bolts. # Step 13 Turn the Malibu on to turn on the power brake assist and press the brake pedal until the pedal becomes firm. Turn the vehicle off. # Step 14 Place the cover back onto the brake fluid master cylinder. # Step 15 Place the tire back onto the wheel studs and secure it with the lug nuts. Remove the Malibu from the jack stands and tighten the lug nuts with the tire iron.
No
Dot 3
I tried today, it looks like the 1995 wheels do not have the clearance for the brake caliper assembly on the 2005, it does not let the wheels turn after installation.
It is called a 10MM aleen head sockit
Use a screwdriver between caliper and front of piston to squeeze piston back, remove caliper via two bolts on rear inside of caliper. Slide caliper away from rotor and support to ensure you don't damage the hyd. hose. Remove pads from caliper, fit new ones same way. re-fit caliper.
Any standard Dot 3 fluid is appropriate.
Large Allen wrench to take two bolts out from inside of brake. This allows the brake pads to come out with the top of the caliper. Inside pad snaps in, outside pad has catches that fit in holes in the caliper. Large spring should be reconnected after bolts are snugged. Quite simple once you've taken a look at it.
The 2005 Dodge Grand-Caravan has 12 valves.
The 2005 Dodge Grand-Caravan has a V6 engine.
A person can find pictures of the rear disc brake assembly for a 2005 Dodge Grand Caravan can be found in a Chilton's automobile repair manual. A manual like this can be found in most libraries and at automobile parts stores.
The 2005 Dodge Grand-Caravan has a 4-speed automatic.
The 2005 Dodge Grand-Caravan is a gas-powered vehicle.