answersLogoWhite

0

Since most knitting is done by using a pattern, you need to follow the directions you are given. Most patterns will tell you to knit around, or back and forth, depending on the end result desired. If you want a sleeve that is already round (with no seams), you knit around and around. If you want a flat finished piece to sew into a seam, or use flat (such as a placemat)go back and forth.

User Avatar

Wiki User

18y ago

What else can I help you with?

Continue Learning about Art & Architecture

Can doctors fix severed arteries?

Unlikely. Doctor is a title for academic achievements. Docters however, stich up arteries regularly.


How do you operate or sew with a sun hand operated sewing machine?

Just bought one of these at an antique shop and was totally befuddled, but I'm an engineer so I enjoy the puzzle of getting things to work. Here's what worked for me, just successfully sewed up the bottom of a pants pocket. Make sure that the thread will flow freely from the spool, through the two metal eyelets (looks like the end of a safety pin), and through the needle hole. If there's any resistance it will bind up. There's a thing on the side that looks like a pulley with a spring that you'd think the thread should go through but it doesn't. That's only to hold the thread when you're not using it. I held it with the sharp end of the needle pointing away from me and the spool nearest my body, but you can probably do this either way. To get started, have the thread through the needle but NOT into the bottom of the machine. Pull about an inch or two of thread out the front (away from your body). To start the sewing, lift the metal flange on the bottom (has two metal tabs on it and the hole that the needle will go through) and insert the fabric under it so that the needle will just barely touch the edge of the fabric when you squeeze. Each time you squeeze, the machine will pull the fabric through one stich-length, but you have to be sure that it's not binding. After the first few stiches, pause and make sure the end of the thread isn't caught under the flange, it likes to get caught there and give you trouble. Pull the end of the thread away from there. After that, keep squeezing, make sure you squeeze it all the way down each time. Also make sure that the fabric sides easily through the flange. If there are folds in the fabric it might try to bind up. Any binding pretty much screws up the stich, so be careful. When you get to the end of the stich, pull it out a few inches so you have some thread to tie off so the seam doesn't unravel. Do the same for the end you started with. When you're done, secure the thread in that spring pulley so that it doesn't unwind itself in the drawer. I didn't find anything on how to work this other than this unanswered question, so hopefully this helps someone!


Will a Greist or Singer Buttonholer work with your sewing machine?

Greist/ Singer buttonholers are attachments for sewing machines that make buttonholes based on templates. There are a variety of buttonholers (see link at bottom).First, pay attention to whether the foot is for verticalor slant-shank machines. Also, if your machine does not create a zig-zag stitch you must use one for straight-stitch only machines. If you machine does have zig-zag capabilities, you may be able to use either type. Most attachments originally came with a feed-dog cover. If you can drop the feed dogs, you should not need the feed-dog cover.While these attachments can fit a variety of machines, including modern machines, they might not fit or work properly.This is a list of known machines and which type of buttonholer will work.* XR-65t: Straight stich - yes.=== === === === * Memorycraft 1000/1001: Griest high shank doesn't work.Pfaff* 261 (low shank): Singer professional buttonholer fits and works, but the action of the pfaff seems to be too wide and spreads out the stain stitches far too much.* 2014: No, walking foot gets in the way.* Designer I: Straight stitch works as long as the calw is large enough. * Scandinavia 200: Singer professional for zig-zag works.


How do you defeat experiment 221 in Kingdom Hearts Birth by Sleep?

When defeating 221 aka Sparky you want to keep a lot of potions or high potions and only 1 or 2 magic panels. 221 has 4 basic modes; ground, air, guns, and pad. When hes on the ground he will start to charge himself with energy, run away from him or attack him to cancel the effect then run from him before he makes an orb of thunder. When in the air dash away from his aerial dash or block by pressing the square button. When he is on the pad you previously saw Stich on he will make orbs of light and dark, like the ones you fight in the beginning. Attack then because he is weaker but be cautious because the orbs will hurt you as well as 221. when he hacks the guns run or block based on how well your block panel is leveled up. If you chose to use a D-Link in this battle use Aqua or Cinderella because they have healing spells as well as great finals. When doing this use a strong keyblade. (I personally liked treasure trove the most) in your battle commands mostly have potions and maybe blizzard magic, it may come in handy. in your action commands the reprisal: counter hammer will not be effective so use most aerial reprisals. in your shot lock commands use dark volley because it is more effective. You may not get it the first time so don't get frustrated and don't give up just try again. That's it. I really hope i helped you.


What is a Disney movie starting with the letter S?

SpongeBob squarepants squidwardthat's all i can think of at the moment.......if i think of more I'll add them!AnswerSnoppy (The dog in Charlie Brown) Sleeping Beuty, Snow white, & Snoopy:)Scooby Doo