0
What else can I help you with?
How can a folded mountain happen in the middle of a tectonic plate?
The tectonic plate boundaries come together and push up on each other to form mountains.
How can you tell if your engine is warped after blowing a headgasket and if it is worth repairing?
Get a good straight edge and some feeler gauges. Lay them across the surface of the head in all orientations. (across front/back/middle, diagnally across corner to corners) See if the feeler gauges will slip under at the end or the middle of the straight edge. (or you can see light...) If so, it's warped. How warped is too much? If I can get my finger nail under it, it gets some attention. Keep in mind that having it planed will make the surface flat, but bolt it up now and the camshafts are now continuously being bent ever so slightly... Heads can now be heat straightened. This brings the cams back in too. If it's not bad and you don't have a Torque to Yield head bolt setup, I've over torqued the head bolts by up to 10% to compensate on minor warpage. Seems to work. No leaks yet, although all car guys will probably say I'm on crack. Most common seems to be heads warped away from the block in the middle. This is where I over torque the bolts just a tad in a reducing pattern out from the center. So, if the head called for 70 ft pounds I'd torque the middle bolts to about 78, next row out to 75, and so forth. Don't blame me if it doesn't work for you or you snap off bolts. answer answer engine wont be warped but the head may be if you didn't overheat engine too much and fixed problem pretty quick, it wont be warped above answer says about bent cam. that is bogus but if head is warped, just go buy anew one and replace specially if aluminum they cannot be straightened if torque says 70 use 70.if u snap a bolt off going over the proper torque then you got to generally take head off and hope there is enough broken bolt showing to be able to remove it with out drills and easy outs PS a camshaft will break before it bends.
Does Alabama have mountains?
Yes, there are mountains in Alabama. The Appalachian Mountains, which are about 1,500 miles in length, extend from North-Central Alabama, up through the New England States and into Canada. There are several mountains in Northeastern Alabama, with Lookout Mountain being the most prominent. Further South in the Talladaga Range of the Appalachians is the highest point in the state, Cheaha Mountain, which stands at 2,407 ft.
What type of mountains are the adirondack mountains?
These are upwarped mountains. They form when blocks of Earth's crust are pushed up by forces within Earth. Over time, the soil and sedimentary rocks at the top of Earth's crust erode, exposing the hard, crystalline rock underneath. As these rocks erode, they form the peaks and ridges.
What is the name of the tectonic process that has created many of the mountains in Middle and South America?
Most mountains are formed by convergent tectonic plate movements. In this process, tectonic plates crash into each other causing land masses to rise up out of the ground. These processes have formed many of the mountains in Central and South America.
What does folded mountains form?
In some cases, the folded crust can be pushed up high enough to form mountains.
What is up warped mountain?
Upwarped mountains are mountains that form when forces inside Earth push up the crust.
What type of fault are the Rocky Mountains?
They are dome(up-warped) mountains
What does folding form?
In some cases, the folded crust can be pushed up high enough to form mountains.
What mountains are folded?
Fold mountains are formed from the collision of continental tectonic plates. Since neither plate subducts under the other, the colliding plates wrinkle and fold like a rug being pushed into a wall.
How are folded mountains different from dome mountains?
Folded mountains are formed from the compression and folding of rock layers, typically along convergent tectonic plate boundaries. Dome mountains, on the other hand, are formed by the uplift of a large circular area of rock, often as a result of magma pushing up from below the surface. Folded mountains have a linear shape due to the folding of rock layers, while dome mountains have a more rounded or dome-like shape.
What type of mountain are the Ural mountains?
Folded mountains. These are formed when tectonic plates clashed together and formed in and up.
What is a folded up mountain?
A folded mountain is a type of mountain that forms when tectonic plates collide, causing layers of rock to buckle and fold. This folding process can create long, ridged mountain ranges with distinctive folds and faults in the rock layers. The Appalachian Mountains in the eastern United States are a well-known example of folded mountains.
How are the three types of mountains different?
The three types of mountains are volcanic mountains, folded mountains, and fault-block mountains. Volcanic mountains are formed from volcanic activity, folded mountains are created from tectonic plate movements and compression, and fault-block mountains are the result of faults in the Earth's crust causing blocks of land to move up or down.
Do folded mountains form by plates being pushed down?
Folded mountains form when tectonic plates collide and the crust is compressed and folded due to the immense pressure. The plates are not pushed down, but rather collide, causing the crust to buckle and fold upward to form mountains.
How does plate movement affect the formation of folded mountains?
Plate movement causes the compression and buckling of rocks, leading to the formation of folded mountains. As tectonic plates collide, pressure builds up and rocks are pushed and folded, creating the characteristic folded structure of mountains such as the Himalayas or the Alps. Over time, this continuous compression and folding result in the uplift of the land and the formation of folded mountain ranges.
What type of mountain are ural mountain?
Folded mountains. These are formed when tectonic plates clashed together and formed in and up.
