0
Will silocone or latex caulking delaminate or discolor or blur mirror silvering?
Wiki User
∙ 10y ago
Silicone or latex caulking will it discolor the silver on mirror
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Did Julia Roberts have a silocone injection to her lips?
she's a uniqe person is there something wrong with that
Where is the air conditioner drain on a 1995 jeep grand Cherokee?
It drains into the frame rail. The only way to clean it is by removing the dash board or to pull the carpet back and drill a small hole and seal it with silocone after cleaning the hole.
How can I make a lipo battery pack?
In order to make a lipoly battery pack, there are many precise steps to follow and many supplies needed. Some of the supplies you will need are a voltmeter, double sided tape, clothes pins and silocone wire. For step by step instructions, visit http://www.dream-models.com/eco/LipoPack.html.
Which are largersmoke particles or gas particles?
3 phase ionic temp, pressure relation to atmospheric exchanges of atp,s and molecular weight that has the structural diffussions, on cold temps, and plot associated eddy current relating to polarity motions of the revolotional spinning of the solar system, thus silver iodide, potessium iodides and silocone iodides thus can rest on upper statosheric layer causing amounts to be recorded as pattern and scatter plots in weahter patterns most liky to have ice formation particulates fall out by eddy currents to each log and deployment of silver iodide and silocone halo group iodides on the atomosheric layers that rays enter tp diffuse and cause drought as time is an issue to forcast a rain plot using radio nucleio tide silver isatopes in the iodide halo group, at least I think so, but hey if not, there is alway the profressional to ask, don;t forget now, learning is profressional trade to participate.
How do you fix the back door handle if will not open the back door on a 98 Jeep Grand Cherokee?
maybe you hit the child safety lock its a little flip switch on the door itself were the latch is. You need to take the door trim off and check, the connecting rod from the latch to the lock. The dealer told me I needed a new lock and all I needed was to adjust the conector on the rod. That conector will slip. After I got it adjusted I glued it with some silocone. ######### TRY PUSHING IN ON THE LID THEN PULL LEVER AND LID UP..IT JUST NEEDS PRESSURE RELIVED BEFORE IT WILL OPEN..
How do you change a fuel pump on a 1987 El Camino?
The question you ask is too involved for a proper answer. You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library. disconnect lines at pump. V-8 right? remove bolts that connect it to engine, remove pump.Disconnect plate between pump and egine(bolted on) remove pushrod between pump eccentic arm and the camlobe, coat it with grease and slide it back in, this will keep the pushroad from fallin down while installing pump. Clean all surfaces, use silocone on the plate a nd reinstall, install pump, reconnect lines,,, The 87 has throttle body fuel injection and has an electric fuel pump so the pump is in the gas tank, the tank has to be taken down to change the pump.
Can you replace the battery in a sonicare?
From doing a little research and asking the same question, YES you can. However, would it be worth it? You can pick up a double pack (two heads, two handles (?), one charger, and a travel case) for around 90 dollars from bj's or sams. With that aside you can do it one of several ways. One would to get a wide screwdriver and basically crack it open, though you might break it. The other would require a dremel and a steady hand. You take the dremel and a 1/8" disc (AND SAFETY GLASSES) and cut carefully around the plastic shell where the two halves are joined. Now that you have it open comes the fun part, more breaking stuff free and soldering. This part is kind of a figure it out because it's not that hard process. But it is very time consuming. Back to my first idea of replacing the whole thing. I do not have a step by step, but would recomend a small jar to keep the parts and probably a digital camera to "remind" you how to put it back together. As for putting it back together you will need some silocone or epoxy, they are both messy. Your call. Fifty bucks a piece, or a whole day and possibly a weekend not to mention frustration. Just try to remember how you had to tell yourself you needed this toothbrush in the first place because it was expensive. And yes I do own one and enjoy it. There are other ideas out there, but......... $50. If this isn't the answer you were looking for than I must apoligize.
