0
Usually, prefinished floors are all different though. Most are 3/4" solid wood and those absolutely can. Most glue downs should have enough wood to be refinished. Floating wood is sometimes questionable. You will want to sand an area in a closet or find an old uninstalled piece before you start to be sure.
What else can I help you with?
What types of flooring are considered simple floors?
Simple floors are considered to be easy and straightforward when it comes to installing them in your home. Common examples are pre-finished hardwood, laminate and cork wood floors.
Average cost pre square foot for removal of hard wood floors?
xpgc7
What is the best product for cleaning wood floors?
There are many products available to clean wood floors. A floor with no polyurethane finish should be swept regularly, damp mopped and waxed. For a polyurethaned floor, including almost all pre-finished floors, you can use a mix of one part white vinegar to 3 parts water to mop or sponge clean your floor. You can polish with a product such as Bruce Hardwood Floor cleaner.
What is the per foot cost to install wood floors?
$6-$8 if nailed or glued to plywood $9-$12 in more underlayment is required This would include wood. Nebraska furniture mart charges $2.75 sq ft to install pre finished wood flooring. Carpet corner charges $2.25 for same.
What is the recommended pre stain treatment for preparing wood surfaces before applying a finish?
The recommended pre-stain treatment for preparing wood surfaces before applying a finish is to use a wood conditioner or sand the wood with fine-grit sandpaper to ensure a smooth and even surface for the finish to adhere to.
What are the instructions for using pre-stain wood conditioner on wood?
To use pre-stain wood conditioner on wood, first, sand the wood surface. Then, apply the conditioner evenly with a brush or cloth, following the wood grain. Allow it to penetrate for 5-15 minutes before wiping off any excess. Finally, apply your chosen stain after the wood conditioner has dried completely.
What are the release dates for Ask This Old House - 2002 Refinishing with Spray Paint Installing a Pre-Finished Wood Floor 10-26?
Ask This Old House - 2002 Refinishing with Spray Paint Installing a Pre-Finished Wood Floor 10-26 was released on: USA: 31 March 2012
Do you hurt the value of a Winchester model 70 pre 64 to refinish the wood stock?
yes just sand it and cover it with clear coat
How do you properly use pre-stain wood conditioner to prepare wood for staining?
To properly use pre-stain wood conditioner before staining, first, sand the wood surface evenly. Then, apply the conditioner with a brush or cloth, following the manufacturer's instructions. Allow it to penetrate the wood for the recommended time before wiping off any excess. This helps the wood absorb the stain evenly and prevents blotching.
What is the recommended application process for a pre-stain conditioner before staining wood?
The recommended application process for a pre-stain conditioner before staining wood is to first sand the wood to a smooth finish, then apply the conditioner evenly with a brush or cloth. Allow the conditioner to penetrate the wood for the recommended time specified on the product label before wiping off any excess. Finally, proceed with staining the wood as usual.
How to Choose Between Unfinished and Prefinished Hardwood Flooring?
Hardwood floors offer many benefits. They are attractive, easy to clean, offer a lovely shine that compliments any room, and will last far longer than any carpet. They go with any decor, can be dressed with any area rug, and will increase your home’s value. Making the decision to put hardwood floors in your home isn’t difficult. Choosing the flooring can be more complicated. Here are tips on how to choose a hardwood floor. Pre-finished Flooring: Choosing pre-finished flooring eliminates the steps of sanding, staining, sanding, staining, sanding and applying polyurethane. The floor comes pre-finished, usually with a high quality polyurethane lacquer that is designed to hold up for many years. To allow for this pre-installation application of stain and lacquer, the edges of the boards have to be beveled. This beveled edge can not typically be felt when you are walking on the floors with bare feet. Most people do not notice the beveling once the floor is installed. There are two big downsides to the prefinished flooring. One is that dirt can get stuck in the beveling, making cleaning a little more difficult. The other challenge is that you will have a limited selection of colors to choose from. Unfinished Flooring: When you choose unfinished flooring, you will be choosing flooring that has no factory finish on it. The edges will not be beveled, and the process of finishing the floors will finish off the edges for a completely flat, smooth surface. The great benefit of unfinished wood floors is that you will be able to choose whatever shade of stain you like. There is no limit to the stains you can choose, and you can then top it with your choice of a satin or glossy finish. The great disadvantage to unfinished floors is that you will have to finish them. Finishing wood flooring is not a project for amateurs. Working the sander can be tricky, with the risk of leaving gouges and damage to the wood. Applying the stain can be challenging as there is the risk of leaving overlap marks, dark spots and light areas. Throughout every step, especially applying the stain and polyurethane, all traces of dust must be completely removed. If you are experienced at staining and finishing furniture, and have even stained flooring before, unfinished flooring may be a good choice for you. However, if you do not have any experience at finishing wood products you may want to go with the pre-finished flooring. Your wood floor is an investment in your home. Making the right choice can ensure that you choose the right product for your home.
How should I condition wood before staining it?
To condition wood before staining it, you should sand the surface to remove any imperfections and then apply a pre-stain wood conditioner to help the stain absorb evenly. This will result in a smoother and more uniform finish.
