answersLogoWhite

0

remove the plate on the left side if the transmission case (the one that's right next to the gear shift lever). keep in mind that one of the Allen head bolts (near the top left of the plate) is hidden in a deep hole, and is kind of a bear to reach with a conventional Allen wrench, but it can be done. when that's removed, you'll see the piston where the fluid line connects, with the conventional bleed nipple. from there you can bleed it like you would your brakes.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you adjust valves on a Suzuki gsx1100g?

How do you adjust valves on a suzuki gsxr 1


Can you adjust the clutch on a 2007 suzuki vitara?

Dont think so, it's hydraulic, you could bleed it but u cannot adjust it


Where is the clutch bleeder on a Suzuki 1400 intruder?

On a Suzuki 1400 Intruder, the clutch bleeder is typically located near the clutch master cylinder, which is situated on the handlebars. It is usually a small valve or screw that can be found on the clutch line itself. To bleed the clutch, you would open this bleeder valve and pump the clutch lever to remove air from the hydraulic system. Always refer to the specific service manual for your model for precise details.


How do you bleed the clutch on a 99 Saturn SL1?

bleed clutch Saturn vue 2003


Clutch Bleeding on a 2000 Suzuki Hayabusa?

To perform clutch bleeding on a 2000 Suzuki Hayabusa, start by locating the clutch master cylinder and identifying the bleed valve on the slave cylinder. Use a clear hose attached to the bleed valve, and open it while having an assistant pull the clutch lever to push fluid through the system. Keep an eye on the fluid level in the master cylinder reservoir to prevent air from entering, and repeat the process until clear fluid without bubbles flows out. Finally, close the bleed valve, top off the reservoir, and test the clutch lever for proper feel and engagement.


How much and what weight of fork oil goes in to a 1993 Suzuki GSX1100G?

For a 1993 Suzuki GSX1100G, the front forks typically require about 10 weight fork oil. The total capacity is approximately 500 ml (or about 16.9 ounces) per fork, but it’s advisable to check the service manual for the exact specifications and recommended levels for your specific model and riding conditions.


What causes a 1994 suzuki intruder cable not release for changing gears?

Do you mean that when you pull in the clutch it won't disengage? The Intruder has a hydraulic clutch. It's usually because you need to bleed the air out of your clutch system or that your hydraulic fluid (DOT 4 brake fluid) is very dirty. You do this the same way you would bleed the brakes. George in Seattle


How do you bleed an oil line on a 1987 suzuki outboard?

how do i bleed the oil pump on a 85hp suzuki outboard


How do you bleed the clutch in a 95 Daewoo cielo?

there dry clutch's, run a cable. no fluid. .:. you can't bleed it. :)


How do you bleed the clutch line on a 2004 ford ranger edge?

how do I bleed the clutch system in a 2004 ford ranger


How do you bleed the clutch on a gsx1100g?

remove the plate on the left side if the transmission case (the one that's right next to the gear shift lever). keep in mind that one of the Allen head bolts (near the top left of the plate) is hidden in a deep hole, and is kind of a bear to reach with a conventional Allen wrench, but it can be done. when that's removed, you'll see the piston where the fluid line connects, with the conventional bleed nipple. from there you can bleed it like you would your brakes.


How do you adjust a clutch on a 1998 suzuki intruder?

The Suzuki Intruder has a hydraulic clutch and therefor there is no adjustment.... There is an adjustment on the clutch lever for the distance from the grip, that is all...