0
Several possible aids (assumes METAL parts): (1)Apply Liquid Wrench or similar penetrating product - wait 10 minutes or so, try again. May need to repeat this several times (2) Tap lightly on outer plug socket with a hammer. (3) Use a very LARGE pipewrench (20" or more)-all things equal, the more leverage, the better. A length of pipe can function as an extender to provide even more advantage. (4)If all else fails, apply HEAT to outer joint with a propane torch. This will expand female part of connection and permit better penetration of lubricant. (Be VERY CAREFUL about the immediate environment here-obvious potential fire hazard.
Somewhere in this series of steps, you should see results. If not, I'm stuck. When you replace plug, use high-quality pipe dope or Teflon tape on threads.
What else can I help you with?
how to change a freeze plug on 1996 cougar mercury?
To change a freeze plug on a 1996 Mercury Cougar, first ensure the engine is cool and drain the coolant from the system. Locate the freeze plug that needs replacement, then use a punch or screwdriver to carefully tap it inward to break it loose. Remove the old plug and clean the area before inserting the new freeze plug, ensuring it is seated properly. Finally, refill the coolant and check for leaks.
My Headlights burned out when turning the corner. What would cause this?
i don't think it burned out but rather the wiring is loose take and unplug it use a pick or some small tool to clean your connectors and put a little grease on the prons to keep clean plug back in i don't think it burned out but rather the wiring is loose take and unplug it use a pick or some small tool to clean your connectors and put a little grease on the prons to keep clean plug back in
What is a plug-top?
loose
How do you remove the middle drivers side spark plug from a 1992 S-10 BLAZER VORTEX 6CYL. ENGINE?
What I had to do is to take the plug socket and put it on the plug then take a open end wrench (3/4" I think) and break it loose. I then took a piece of brake tubing and put it over the end of the plug and backed it out that way. To install reverse the procedure. Otherwise you will have to take the steering column loose.
Why does the plug keep falling out of the outlet?
The plug may keep falling out of the outlet due to a loose fit caused by worn-out prongs on the plug or a loose outlet socket.
Is it safe to use a loose plug socket in your home?
No, it is not safe to use a loose plug socket in your home as it can pose a risk of electrical shock or fire hazard. It is important to repair or replace loose plug sockets to ensure safety.
Guitar loose amp plug?
This can happen and may require opening up the guitar to retighten the loose amp plug fitting from inside.
How do you change the rear spark plugs 2000 Bonneville?
First of all, very carefully. Use a spark plug socket with a universal joint, 9' extenstion. have thin arms. Break loose the plug, then remove by hand or rachet/socket.
What would case a ford f150 to leak oil or antifreeze around the spark plug?
This could be a valve cover leak, allowing oil to drip down into the cavity where the plug lies. Clean the area and see if it repeats itself, and look for signs of a leak. A second explanation could be the plug is not seated or tightened correctly and is leaking a bit of the fuel/air mixture out of the plug threads, causing an oily mess there. Gently check to see if the plug is loose, and try replacing the plugs. Be sure all the surfaces around the plug and on the plug itself are clean.
Why does your 1998 jeep miss when you hit a bump?
Look for a loose plug, or plug wire.
Why does your Jeep Wrangler backfire when you hit a bump?
Look for a loose plug, or plug wire.
How do you change transmission oil on a Geo Tracker?
easy take out the drain plug (lower plug) located midway through the transmission using a 3/8 drive. This will drain the tranny oil. Then break the upper plug loose and put the lower plug in and tighten. Slowly fill the tranny with 85w/90 through the upper plug until it flows out of the plug you are filling. Finally install the fill plug and tighten.
