answersLogoWhite

0

To calculate expansion joints in steam pipes, you first need to determine the thermal expansion of the pipe material based on the temperature range and material properties. This involves using the linear expansion formula: ΔL = α × L0 × ΔT, where ΔL is the change in length, α is the coefficient of thermal expansion, L0 is the original length, and ΔT is the temperature change. Additionally, consider the pipe's layout, support conditions, and the type and size of the expansion joint to accommodate the calculated movement, ensuring it can handle the forces and stresses involved. Consulting design standards and guidelines is also crucial for proper sizing and placement.

User Avatar

AnswerBot

1mo ago

What else can I help you with?

Related Questions

What is meant by expansion joint and Where expansion joints are used in refinerieswhythis type joint used now?

Expansion joints are used on long runs (over 100 feet) of pipe or ducts where the expansion of steel will create stress on the pipe or its supports. for every 1 degree change in metal temperature the pipe will expand 6 millionths of a foot per foot of length. on a steam pipe 400 foot long carrying 750 degree steam this expansion would amount to a change in length of the pipe of 1.632 feet. this could tear down the supporting structure if this expansion weren't relieved by an expansion joint every 100 feet. expansion joints could be flexible corrugated pipe, reinforced rubber sheet, sliding pipe joints, or expansion loops, among other things.


Is short radius bend is suitable for steam pipeline?

Sure it is. You need to know, however, where to use it. for long runs of pipe with bends, it would be preferable to use long radius ells, to prevent excessive flexing of the fitting as the pipe expands and contracts due to thermal expansion. However, in short runs (less than 50 feet (or 15 meters)) of straight pipe without expansion joints and less than 300 degrees F (170 C) differential temperature, (steam temp. minus ambient temp.) short radius bends (or elbows) are more than adequate. As the diff. temp. increases the straight runs of pipe should be decreased in length, or expansion joints installed, to prevent excessive flexing at the joints and fittings.


Can a valve be installed at the end of steam expansion loop?

Yes. The expansion loop is only there to take up the thermal expansion of the pipe run, installing a valve will not impede the action of the loop.


Who invented the 's' bend pipe and why?

Eli Whitney after he developed the steam engine to allow for the coefficient of expansion per degree of temperature changes also called an expansion loop


What is a glass pipe steam roller?

a pipe that is a steam rolled a tube with a boll in the middle of it


What is the best method for sealing pipe joints: using pipe dope or Teflon tape?

The best method for sealing pipe joints is using Teflon tape.


What is the effect of water pressure at the pipe joints?

Water constantly exerts pressure on pipe joints. I have seen old soldered joints flying apart when subjected to extreme pressure or trains passing nearby. This sometimes happens with plastic pipe also if joints are not thoroughly set .


What is the best type of pipe dope recommended by plumbers for sealing pipe joints effectively?

The best type of pipe dope recommended by plumbers for sealing pipe joints effectively is a high-quality thread sealant compound.


What are the Advantages of throttling calorimeter?

An instrument utilizing the principle of constant enthalpy expansion for the measurement of the moisture content of steam; steam drawn from a steam pipe through sampling nozzles enters the calorimeter through a throttling orifice and moves into a well-insulated expansion chamber in which its temperature is measured. Also known as steam calorimeter.


Materials used to seal joints steam pipes?

it will be depend on the application, however following material are generaly used for pipe sealing -asbestos sheed - PTFE -composite sheet(Rubber+asbestos)


How a 1 pipe steam system works?

A one-pipe steam system uses a single pipe to distribute steam from a boiler to various heating units, such as radiators. Steam travels through the pipe, heating the units, and then condenses back into water, which returns to the boiler by gravity. The system relies on the principles of thermodynamics, where steam rises and pushes the condensate back down the pipe. This type of system is typically simpler and less expensive to install, but can be less efficient than two-pipe systems.


What is the formula on speed and height through a steam pipe?

The speed of steam flowing through a pipe can typically be calculated using the equation v = sqrt(2gh), where v is the speed of the steam, g is the acceleration due to gravity, and h is the height of the steam pipe. This equation assumes ideal conditions and neglects factors like friction and losses.