The Linear series of garage door operators uses the model MDTK keypad, part number DNT00058. This keypad has no memory, and acts only as a transmitter.
If you would like to see a diagram with step-by-step instructions and pictures detailing the location of the buttons, please feel free to review the attached document.
In order to change the keypad code, you must erase the memory in the LDO/LSO/LCO. If you will look at the upper right hand corner of the left hand side of the LDO/LSO/LCO, you will see the learn button. Simply press and hold this button for 10 seconds or more. When you release the learn button, the red LED above the button will blink 3 times and then come on bright for 15 seconds. When the LED goes out, the memory in the operator is erased. To learn in a new keypad code, press and release the learn button. The LED will come on for 15 seconds. While the LED is on, go to your keypad and enter your desired code (1 to 6 digits long) and press start/stop on the keypad. The LED will blink to indicate receipt of the new code. You will also have to reenter all of your hand held remotes into the memory.
Again, simply press and release the learn button. When the LED comes on, press the button on the remote you wish to use. Repeat for any additional remotes. If you hold the learn button down for 10 seconds or more, you will have to start over, since the memory will be erased again.
The change code process on a garage door keypad involves entering a specific sequence of numbers to reset the access code for the garage door opener. This allows you to change the code to a new combination for added security.
To change the code for your garage door, locate the control panel on the garage door opener unit. Enter the current code and press the "Learn" button. Then, enter a new code and press the "Learn" button again to save the new code.
To change the garage door code, locate the control panel on the garage door opener unit. Enter the current code and press the "Reset" or "Learn" button. Then, enter a new code and press "Enter" or "Set" to save the new code.
To change the garage door keypad code, locate the "Learn" button on the garage door opener motor unit. Press and release this button, then enter your desired new code on the keypad. Press the "Enter" button to confirm the new code.
To change a garage door code, locate the control panel on the garage door opener unit. Enter the current code and press the "Learn" or "Program" button. Then, enter a new code and press "Enter" or "Learn" again to save the new code. Test the new code to ensure it works properly.
To change your garage door code, locate the control panel on the garage door opener unit. Enter the current code and press the "Reset" or "Learn" button. Then, enter a new code and press "Enter" or "Set" to save the changes. Refer to the manufacturer's instructions for specific steps.
To change your garage door code, locate the control panel on the garage door opener unit. Enter the current code and press the "Reset" or "Learn" button. Then, enter a new code and press "Enter" or "Set" to save the changes. Refer to the manufacturer's instructions for specific steps.
To change the garage door code for added security, locate the control panel on the garage door opener unit. Enter the current code and press the "Reset" or "Learn" button. Then, enter a new code and press "Enter" or "Set" to save the new code. Test the new code to ensure it works properly.
A linear garage door opener keypad allows you to open and close your garage door by entering a code. The features include convenience, security, and the ability to provide access to multiple users. The benefits are increased safety, easy access without a remote, and the ability to control who can enter your garage.
To change the garage door opener code on a Liftmaster, locate the "Learn" button on the opener unit, press and release it, then enter a new code on the keypad within 30 seconds.
To change your garage door opener code, locate the "learn" button on the opener unit, press and hold it until the indicator light blinks. Then, enter your desired new code on the keypad and press the "learn" button again to confirm. Your garage door opener code should now be changed.
To change the code on a garage door opener, locate the "learn" button on the opener unit, press and hold it until the indicator light turns on, then enter a new code on the keypad or remote control.