answersLogoWhite

0

Looking at the brush, remove the two screws from the black plate holding the brush. There are two clips that holds this plate once you remove the screws. This should be easy to remove with a flat type screw driver. Now is the tricky part to remove the top cover of the vacuum so you can access the compartment to put the belt on. The whole top part of this vacuum comes off. If you look above the part where black plate was, there are two more clips on the top left and top right hand corner. These two hold one end of the top cover. It is not as simple as pushing the clip to one end to slide out. You have to find a gap between the edge of top cover and bottom structure(right next to each clip) and shove the flat screw driver in and push the top cover away from the bottom structure and push down the top cover. You will notice that there are invisible hinges between the two which locks in the top cover.

Do the same procedure for the bottom right and left edges(right next to each end of the brush) of the vacuum and separate the two(bottom structure and top cover) out using the flat type screw driver..

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

What is the price range on a new Bissell Vacuum?

The price of a Bissell Vacuum will vary based on the power, size and design of the specific vacuum. Generally, these cleaners are selling for approximately å£80 or $120.


Who makes the Power Clean vacuum?

The Power Clean Multi Cyclonic Bagless Vaccum is made by Bissell Inc., also known as Bissell Homecare. It was founded by Melville Bissell in the 19th century and is headquartered in Walker, Michigan.


What does the vacuum pump do in an engine?

You must have a diesel. The vacuum pump is what gives you POWER BRAKES and on the newer engines it also makes the power steering work. Only a gas engine makes vacuum. A diesel engine does not make vacuum, so they install a vacuum pump.


How much force can a vacuum cleaner exert?

The force exerted by a vacuum cleaner is typically measured in terms of air watts or suction power. A typical household vacuum cleaner can have a suction power of around 100-300 air watts, which is equivalent to around 16-40 kPa of pressure. Commercial or industrial vacuum cleaners can have higher suction power reaching up to 400-500 air watts.


Where do you run the vacuum line from the turbo 400 trans modulator to an edelbrock performer 800cfm carb?

When you get ready to run the vacuum line from the turbo 400 trans modulator to an Edlebrock Performer 800 CFM carb, attach the vacuum line for the transmission vacuum modulator to the bottom constant vacuum source or the plug that is below the throttle plate. After that, install the vacuum advance to the port that is signaled or right above the throttle plate. Once that is completed, install the large vacuum line to the back of the carb for the power brake.


How do you install the power head on a Kirby vacuum cleaner?

On the front, there is a square piece that twists. If you turn it 180 degrees you can take the front right off.


Bissell pro heat will not work?

If your Bissell ProHeat is not working, try checking to make sure it is plugged in properly and that the water tank is securely in place. Also, check the power switch and ensure it is turned on. If the issue persists, consult the user manual for troubleshooting tips or contact Bissell customer support for assistance.


Loss of power brakes on 1995 Saturn SC1 DOHC?

"Power Brakes" are actually "vacuum assisted brakes", meaning that a vacuum diaphragm is used to provide additional force against the brake pedal as you attempt to stop your vehicle. If the engine vacuum has decreased, through wear, timing issues or because of a vacuum leak, there will be considerably less of the vacuum assist available when you stop your vehicle. First, check for a vacuum leak, and make certain that you include the vacuum assist module. If there are no vacuum leaks, check the vacuum that the engine is creating; if that's not the problem then you may have a leaking or damaged master cylinder.


Does a vacuum with a bag have more power than a bagless vacuum?

No the bag does not effect how much power their is.


How do you install oil pressure gauge on 00 civic?

If it is vacuum a gauge oil filter. You have to buy a 3/8 pipe t fitting to fit the block and install both the sensor and the gauge tube on. Key on power wire to light it up.


Where do your vacuum lines hookup to your power brake system?

The vacuum lines for your power brake system typically connect to the intake manifold of the engine. This location allows the vacuum created during engine operation to assist in the brake booster function. The brake booster then uses this vacuum to amplify the force applied to the brake pedal, making braking easier and more effective. Proper connections and condition of these lines are crucial for optimal brake performance.


What does the vacuum booster do?

It's the "power" in your power breaks.