answersLogoWhite

0

Answer Well its about getting the right products for the job. Depending on what type of project is going on but here are the basics. floor preparation. if starting on plywood there must be a subfloor for the mortar to adhere to. this can be cement backer board, the floor can be mudded with a self leveling mortar. Cement backer board is the most common use. it come in quarter to half inch thick sheets and can be cut with a razor knife (score and snap then cut), or cement sheers (dewalt has some). cover entire floor. Then buy mortar either custom building product which can be found depot, or other such as mapei or laticrete. a knotch trowel is needs (size of trowel depending on tile size). mix mortar and follow directions on the bag. mix in 5 gallon bucket with drill and mortar mixer attachment. but before this measure and see how you want to tile layed on the floor. it is good to mark with chalk, also measure two points off a wall to make sure you are square the the wall. tile spacers are a good idea. this helps leave room for the grout and keeps everytile square to each other. spread mortar evenly to an area with knotched trowel, but only an area to only til about 4-6 tiles at one time, then repeat the process. do no mortar the whole floor first and dont rap ourself in a corner. lay the tile where you want it and press down firmly. wipe excess mortar on edges of tile. there are parts that you can use for room to room transitions, like carpet to tile. find one you like and tile to it and follow instructions. once finished let dry for 24 hours. then grout. (24 hours is excessive, in my opinion, considering the temperature and humidity of the house, 8-12 hours should be plenty)

throw the spacers away, pop a chalk line square to one of the walls, a long exterior wall would be best. measure your tiles, measure several as they will vary slightly and get a good average size, if you're using 12"-18" tile, double your average size of the tile and add 1/2" for grout lines. pop a line parallel the other chalk line exactly that dimension away (2 tile sizes + 1/2"). continue across the room(s). now you need a line perpendicular to these lines, laser square works best but there are plenty of ways to get a perpendicular line. you can check by popping the line and and then popping another parallel the same dimension away from that line (2 tile sizes +1/2"), then measure corner to corner diagonally on the square it creates, both directions. these dimensions should be as close as possible, if the lines are perpendicular, these dimensions will be exactly the same. once you have those lines, continue to pop the rest in that direction using the same dimension throught the room(s). you will now know where every tile will be placed and can actually make every cut you need before mixing your thinset. when you're ready to install, trowel your mortar in one square at time and install 4 tiles in the center of this square. your grout lines will be straight and much more consistent than using the spacers

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How to lay floor tiles effectively and efficiently?

To lay floor tiles effectively and efficiently, start by preparing the surface, measuring and planning the layout, applying adhesive evenly, and placing the tiles carefully. Use spacers to ensure even spacing, and grout the tiles once they are set. Finally, clean the tiles and seal the grout for a finished look.


How is subway tile installed in a home?

You must make the measurements that you need to lay the tile, then lay out the tiles on the floor to help familiarize yourself with the pattern you are going to be working with. Lay your grouting adhesive and then finally the tiles.


How can I effectively lay floor tiles in my home?

To effectively lay floor tiles in your home, start by preparing the surface, measuring and planning the layout, applying adhesive, placing the tiles, and grouting the joints. Make sure to use the right tools, follow the manufacturer's instructions, and take your time to ensure a professional finish.


How to lay ceramic tiles on a concrete floor?

To lay ceramic tiles on a concrete floor, first clean and prepare the surface. Apply a layer of thin-set mortar using a trowel, then place the tiles in a desired pattern. Use spacers to maintain even spacing between tiles. Allow the mortar to dry completely before grouting the tiles. Finally, seal the grout to protect it from stains and moisture.


How to lay floor tiles on concrete effectively?

To lay floor tiles on concrete effectively, start by cleaning and leveling the concrete surface. Apply a layer of thin-set mortar, then place the tiles in a pattern of your choice. Use spacers to maintain even spacing between tiles. Once the tiles are set, apply grout between them and wipe off excess grout with a damp sponge. Allow the grout to dry completely before walking on the tiles.


What way do you lay 600x300mm floor tiles as you enter a room?

You center the floor tiles to the center of the door.Normally a door with is 36 inches. A typical floor tile is 12 inches. Therefore the tiles would be set in the door in this order (6 - 12 - 12 - 6 = 36), adjust for grout widths. The same applies to mm tiles.


How can I effectively lay tiles on a concrete floor?

To effectively lay tiles on a concrete floor, follow these steps: Clean and prepare the concrete surface by removing any debris or dust. Apply a layer of thin-set mortar to the floor using a trowel. Place the tiles on the mortar, pressing them firmly into place. Use spacers to ensure even spacing between tiles. Allow the mortar to dry completely before grouting the tiles. Apply grout between the tiles, wiping off excess with a damp sponge. Seal the grout to protect it from stains and moisture.


How to lay a mosaic tile floor effectively and efficiently?

To lay a mosaic tile floor effectively and efficiently, start by preparing the surface, applying adhesive, and laying the tiles in a pattern. Use spacers to ensure even spacing between tiles and allow the adhesive to dry before grouting. Finish by applying grout and sealing the tiles for a polished look.


How to lay tile floor effectively and efficiently?

To lay tile floor effectively and efficiently, start by preparing the surface, measuring and planning the layout, applying adhesive, setting the tiles in place, and grouting the tiles once they are set. Make sure to use the right tools and techniques for a professional finish.


How do you properly lay floor tile to ensure a professional and durable installation?

To properly lay floor tile for a professional and durable installation, start by preparing the surface, applying adhesive evenly, laying the tiles in a straight pattern, using spacers for even spacing, and grouting the tiles once they are set. Finally, seal the grout to protect the tiles and ensure longevity.


Can you lay floor tiles over water based paint spray on floor?

You " CAN ", but it is not advisable!AnswerSand the painted area so that it is rough. Then the adhesive will work better.


What is a good name for a tiles business dealership?

Square Deals! the floor tile superstore. Floor Tiles by design, All the pretty tiles! Floor Tiles R US Floor tiles & More Your City Tile! Miles O tiles! Decorator tiles for you