answersLogoWhite

0

That keypad (stamped with a model # of 31D302 A) goes along with a console single button controller. The whole pakage is called a touch code transmitter model 139.18755. The keypad is programmed so simply that you'll kick yourself.

  1. Find the console (single button controller) that the keypad is wired to
  2. Remove the small plastic faceplate above the button using a small flat screwdriver
  3. You should see a 9v battery inside this compartment (it probably requires replacement while you have it apart)
  4. You should also see a small black switch on the right side of the opening (it should be labeled "program" or "operate")
  5. Move the switch to "program"; the red led light will start to flash on the keypad
  6. Go to the keypad and enter your new 4 digit code (nothing more than 4 digits)
  7. Go back to the console and move the switch back to "operate"; the red light will stop flashing
  8. Test your code on the keypad at this point, it should work, if it doesn't, repeat steps 5 thru 8

It's too simple.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do I program my Genie garage door opener keypad?

To program your Genie garage door opener keypad, first locate the "Learn Code" button on the opener motor. Press and release this button, then enter your desired PIN on the keypad. Press the "Program" button on the keypad to save the code. Test the keypad by entering the PIN and pressing the "Open/Close" button.


How can I program a garage door keypad?

To program a garage door keypad, follow the instructions provided in the user manual of the keypad or the garage door opener. Typically, you will need to locate the "learn" button on the opener, enter a specific code on the keypad, and then press the "learn" button to sync the two devices. Make sure to choose a secure code and test the keypad to ensure it is working properly.


How can I replace my garage keypad?

To replace your garage keypad, follow these steps: Remove the old keypad by unscrewing it from the wall. Purchase a new keypad that is compatible with your garage door opener. Install the new keypad by following the manufacturer's instructions. Program the new keypad with a unique access code for security. Test the new keypad to ensure it is working properly.


How do you program a keypad garage door opener?

To program a keypad garage door opener, you typically need to follow the manufacturer's instructions provided in the user manual. This usually involves entering a specific code or sequence of buttons on the keypad to sync it with the garage door opener system.


How can I program a LiftMaster garage door opener keypad?

To program a LiftMaster garage door opener keypad, you typically need to locate the "Learn" button on the opener unit, enter a specific code on the keypad, and then press the "Enter" button. This process allows the keypad to communicate with the opener and operate the garage door. Refer to the manufacturer's instructions for specific steps and codes.


How can I program a universal garage door opener keypad to work with my garage door?

To program a universal garage door opener keypad to work with your garage door, follow the instructions provided in the keypad's manual. Typically, this involves locating the "learn" button on your garage door opener, entering a specific code on the keypad, and then pressing the "learn" button to sync the two devices.


How do I program the Chamberlain garage door opener keypad?

To program the Chamberlain garage door opener keypad, you typically need to locate the "Learn" button on the opener unit, press it, then enter a code on the keypad followed by the "Enter" button. Refer to the specific instructions in the user manual for detailed steps.


How can I program a garage keypad?

To program a garage keypad, follow these steps: Locate the "Learn" button on your garage door opener. Press and release the "Learn" button. Enter a new PIN code on the keypad. Press the "Enter" or "Learn" button on the keypad to confirm the new code. Test the new code by entering it on the keypad and opening the garage door. Make sure to consult your garage door opener's manual for specific instructions.


Can you reset 2002 ford explorer keypad system cannot program keypad 2 work turnd ignition sw offon 8X locks signal in mode but keypad does not program bcuz messed it up while adding a new keypad?

On my 1997 8x places a new remote and 10x clears all remotes so you can start all over with new remotes.


How can I program a Chamberlain garage door keypad?

To program a Chamberlain garage door keypad, you typically need to locate the "Learn" button on the garage door opener unit, press it, then enter a PIN on the keypad followed by the "Enter" button. This process may vary slightly depending on the specific model of your Chamberlain keypad and garage door opener. Refer to the user manual for detailed instructions.


How do you program a garage door opener keypad?

To program a garage door opener keypad, you typically follow these steps: locate the "learn" button on the garage door opener motor, press the button, enter a code on the keypad, and then press the "learn" button again to confirm. This process allows the keypad to communicate with the garage door opener and open the door when the correct code is entered.


How can I program a LiftMaster garage door keypad?

To program a LiftMaster garage door keypad, follow these steps: Locate the "Learn" button on your garage door opener. Press and release the "Learn" button. Enter a 4-digit PIN on the keypad. Press the "Enter" button on the keypad. Test the keypad by entering the PIN and pressing the "Enter" button to open the garage door. If you encounter any issues, refer to the user manual or contact LiftMaster customer support for assistance.