The driveshaft is removed to replace the clutch by unbolting the u-joints and retaining caps on each end of the drive shaft. The shaft can then be collapsed slightly to allow for easier removal.
remove the nearside driveshaft & and just pull the box asside thus giving u plenty of room to renew the clutch with it sitting on the subframe. hope this helps. remove the nearside driveshaft & and just pull the box asside thus giving u plenty of room to renew the clutch with it sitting on the subframe. hope this helps.
Remove the driveshaft, jack up the transmission, remove the clutch slave cylinder, detach the bell housing bolts, move the transmission back, remove the shift fork, clutch plate, pressure plate, flywheel and throwout bearing, use alignment tool that came with new clutch to install new pressure plate, clutch disk and throwout bearing.
To replace the clutch in a 1994 Toyota truck, start by disconnecting the battery and removing the transmission. You’ll need to remove the driveshaft, exhaust components, and any other parts obstructing access to the transmission. Once the transmission is out, you can remove the old clutch assembly and replace it with the new one, ensuring to align it properly. Finally, reassemble the components in reverse order and reconnect the battery.
Block the wheels, place a transmission jack under the transmission and secure the transmission to the jack, unbolt the flywheel, drop the transmission, remove the pressure plate and clutch plate, replace the pressure plate, attach the clutch plate and ensure you torque the bolts to manufacturer's specifications (this is especially important), remove your alignment tool, replace the transmission, reinstall the driveshaft.
To replace the clutch on a Chevy Colorado, first, lift the vehicle and remove the transmission by disconnecting the driveshaft, exhaust components, and any electrical connections. Once the transmission is out, unbolt the pressure plate and remove the old clutch disc. Install the new clutch disc and pressure plate, ensuring proper alignment, then reassemble the transmission and reconnect everything. Finally, lower the vehicle and test the clutch operation before driving.
To replace the clutch on a 1991 Mazda Miata, first, disconnect the battery and lift the car securely. Remove the transmission by detaching the driveshaft, shift linkage, and bellhousing bolts. Once the transmission is out, you can access the clutch assembly; replace the clutch disc, pressure plate, and throw-out bearing. Reassemble by reversing the disassembly steps, ensuring all connections are secure before testing the new clutch.
Remove the transmission. Remove the clutch plate and springs. Remove the clutch. Reverse the process to install the new clutch.
Unbolt/remove driveshaft. Use U-joint press to remove old U-joint, install new and replace driveshaft.
To change the clutch on a 1977 F250 4x4, start by disconnecting the battery and removing the driveshaft to gain access to the transmission. Next, unbolt the transmission from the engine and lower it carefully. Remove the old clutch assembly, including the pressure plate and flywheel, and replace them with the new components, ensuring proper alignment. Finally, reassemble the transmission, driveshaft, and reconnect the battery.
Easy, step one: loosen the idler wheel tensioners. #2 remove the bolts that hold the skid to the tunnel and remove skid #3 remove chaincase cover and driveshaft bearing #4 remove speedometer cable from clutch side driveshaft bearing cover and driveshaft bearing #5 slide driveshaft towards chaincase enough to slide the track out.
go to 99intrigue.shutterfly.com/compressor. Get clutch remover and installer. Get feeler gauge. Remove serpentine belt with 1/2" breaker bar. Measure air gap in clutch. Remove shaft nut. Remove clutch with remover. Remove outer snap ring. Remove pulley with pry bars or remover. Remove clutch coil with pry bars or remover. Replace new coil and pulley. Replace snap ring. Replace clutch, maintaining air gap. Reinstall nut. Reinstall belt.
you will have to remove the transmission. once you have the tranny off you can remove and replace the clutch...if you buy a new clutch specific directions will come with it...too long to write here.