0
To remove the rear seat on a 2008 Chevy HHR, first, locate the two release levers at the base of the seat cushion. Pull these levers upward to release the cushion, then lift it out of place. For the seatback, find the bolts securing it to the floor or the back of the vehicle and remove them using a socket wrench. Once the bolts are removed, simply lift the seatback out of its position.
What else can I help you with?
Where is the spare tire in a 2008 hhr?
In a 2008 Chevrolet HHR, the spare tire is located under the rear cargo floor. To access it, you'll need to lift the cargo cover and remove the panel or storage area that conceals the spare tire compartment. The spare tire is secured in place with a mounting bolt that can be loosened with the included tools.
What size star wrench is needed to remove seat belt from 2010 Chevy hhr?
To remove the seat belt from a 2010 Chevy HHR, you'll typically need a T50 Torx star wrench. This size is commonly used for the bolts securing the seat belt assembly. Always ensure you have the correct tools and consult the vehicle's service manual for specific instructions.
Chevy HHR 2008 keyless remote reset?
how to reset Chevy 2008 hhr keyless remote
Will 22's fit on a 2008 Chevy hhr?
22s will fit on the hhr on stock suspension.but if you have a lowered suspension they might rubb!i have 20s on my hhr,with lowering springs.
Where is the battery on a 2008 Chevrolet HHR?
The battery is in the rear compartment with the spare tire.Its placed there to protect it from extreme temperatures in the engine compartment.Should make the battery last longer.
Change hhr tail light bulb?
What is the part number for the 2008 HHR tail light bulbs and backup light bulbs?
Where is the 2008 hhr front passenger side airbag cutoff switch?
In the 2008 Chevrolet HHR, the front passenger side airbag cutoff switch is typically located on the right side of the dashboard, near the glove compartment. You may need to open the glove box to access it. The switch allows you to enable or disable the passenger airbag, often used when a child seat is installed in the front passenger seat. Always refer to the vehicle's owner manual for specific details.
Where is the camshaft position-acuator on Chevy hhr 2008?
Replacement of a 2008 Chvy Camshaft Sensor
How do you replace fuel pump on Chevrolet HHR?
To replace the fuel pump on a Chevrolet HHR, first ensure safety by disconnecting the negative battery cable and relieving the fuel system pressure. Remove the rear seat to access the fuel pump access panel, then disconnect the electrical connectors and fuel lines from the pump. Unscrew the retaining ring to lift out the old pump, install the new pump in reverse order, and reconnect the fuel lines and electrical connectors before reassembling the access panel and seat. Finally, reconnect the battery and check for leaks before starting the vehicle.
Where is the oil drain plug on a 2008 Chevy HHR?
On the backside of the oil pan.
Where is the tire pressure module for a 2008 hhr?
In a 2008 Chevrolet HHR, the tire pressure monitoring system (TPMS) module is typically located underneath the vehicle, near the spare tire well or along the rear frame. It is integrated with the vehicle's body control module (BCM). If you're looking to check or replace it, it's advisable to consult the vehicle's service manual for specific instructions and locations.
Where is the sdm 2008 hhr?
The SDM 2008 HHR refers to the Service Data Module in the 2008 Chevrolet HHR, which is typically located under the dashboard near the steering column or in the fuse box area. If you're looking for a specific component or need to troubleshoot an issue related to the SDM, it's advisable to consult the vehicle's service manual or a professional mechanic for precise guidance.
