0
You will need to remove the ignition switch retaining ring. Pull the ignition switch barrel out. Remove the wiring harness from the back of the ignition switch. Reverse the process to install the new ignition switch.
Begin by removing the retaining ring at the top of your ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.
if you have the key and wish only to change lock mech.because of failure.in bottom side of ign is small hole with key in and in either on or acc position push up into hole with small nail,drill ect you will feel spring loaded resistance .with that pushed in ,assembly will pull out.cheap like 15.00 bucks for new at Canadian tire .
Add your answer:
Earn +20 pts
How do you replace an ignition switch on a 2001 Monte Carlo ss 3.8?
Begin by removing the retaining ring at the top of your 2001 Chevrolet Monte Carlo ignition switch. The ignition switch barrel will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.
How do you change a ignition switch on a 2001 Chevrolet Camaro?
The 2001 Chevrolet Camaro ignition switch is held in place with a retaining ring. Remove the retaining the ring and slide the ignition switch out. Remove the wiring harness. Reverse the process to install the new ignition switch.
How do you replace an ignition switch on a 2001 Buick Regal GS?
http://www.automotivehelper.com/topic1054152.htm or Goole "ignition switch replacement 2001 regal"
How do you change ignition coil in Nissan sentra 2001?
How change my ignition switch nissan 2001 sentra.
How do you disarm the alarm on a 2001 Monte Carlo?
To disarm the alarm, you use the key to unlock either the front door, press the unlock button on the keyless entry transmitter. Insert a valid key into the ignition and switch the ON position.Ê
How do you program a keyless remote for a 2001 Chevy silverado?
# # Close all the vehicle doors. # Insert the ignition key into the ignition lock cylinder. # Press and hold the door unlock switch. # While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. # Release the door unlock switch. The doors will lock and unlock to confirm the program mode. # Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter. # Repeat the previous step to program up to four transmitters. # Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode. # Operate the transmitter functions in order to verify correct system operation.
Will a 2001 ignition switch fit the 2000 Chevy Tracker?
Yes, the 2001 ignition switch for a 2000 Chevrolet Tracker will fit just fine. Other years the switch fits are 1999 to 2004.
How do you change the ignition switch on a 2001 Sunfire?
I recenlty got a recall on my ignition switch in my 2000 sunfire and I just took it to the dealer and they did it for free.
How do you unlock a stuck ignition switch on a 2001 Jeep Cherokee Sport when manipulating steering wheel or brakes won't help?
You probably need to get an automotive locksmith to pull out the barrel of the ignition, clean it out and open up the "vee" that allows the levers to turn.
Can you use a 2002 ignition switch on a 2001 Chevy Impala?
YES.....
Where is the ignition switch on 2001 intrigue?
See the link for a 2000 location. The 2001 procedure ought to be about the same.
Why would 2001 Pontiac Gran Prix SE ignition switch cause intermittent electrical problems with AC fan and lights?
ignition switch or key and tumbler.
