0
Raise the rear wheel off the floor enough to rotate the engine in 5th gear..
1 remove the spark plugs
2 find TDC of the front cylinder ( compression stroke - both valves closed LOL)
3 depending on the tester you use setup is a little different. I have a cheap one from Harbor freight. It only tests at about 15lbs. ( 100 would be preferred )
Setup tester by regulating the input pressure to zero the leakage gauge.
4 screw adapter into the plug hole and connect the tester.
5 I use my ear and a mechanics stethoscope to listen for leakage. Air will be hissing and could be heard through the intake or the exhaust valves if there is a problem. Also if the valves are OK the rings may be weak and you may see bubbling in the oil tank..lastly a head gasket OR ALL IS GOOD
6 Acceptable leakdown is about 20% on my tester
My gage has an area indicated by green that is an acceptable amount of leakage.
Good Luck - Keith
What else can I help you with?
How do you load test a Harley Davidson motorcycle battery?
You can take it to a battery place and they can test it under a load.
How do you test a Harley Davidson alternator?
This procedure is covered in detail in the proper manual for your model
How do you test an Ignition coil for a 2003 Harley Davidson Heritage Softail Classic Carborated?
Use an ohmeter to test tesistance where the plug wires connect to the coil-it should read 12,000. now for the the primaray side where the signal wires connect to the coil should be 2-3 ohms.
What is the starting price for the 2013 Harley Davidson Heritage Softail Classic?
The starting price for the 2013 Harley-Davidson Heritage Softail Classic is $17,599. This price is for the vivid black color only. One can go to the manufacturer's website to search for dealers near them or to arrange a test ride with a local dealer.
How do you check for bad cylinder heads on your 305?
compression test or leak-down test.
What you must do to inspect the drink tube assembly?
perform a tube leak test perform a tube leak test perform a tube leak test perform a tube leak test perform a tube leak test perform a tube leak test perform a tube leak test
Where can you get an engine leak test other than at a mechanic shop?
Here are several answers and opinions from FAQ Farmers: * McDonalds? I mean, c'mon, where else would you get an engine leak test besides from a mechanic? Unless your cousin Louie has the equipment. * A leak down test requires a special fitting, which screws into the spark plug hole, and an air compressor. Anyone who has this equipment can do a leak down test, although understanding the results requires knowledge and experience.
How can you pre- test a voltage regulator on a 1989 Harley Davidson before you install it?
To pre-test a voltage regulator for a 1989 Harley Davidson, use a multimeter to measure the output voltage. Connect the multimeter to the regulator's output terminals, then apply a suitable voltage to the input terminals to simulate operation. The output should read between 13.5 to 14.5 volts if the regulator is functioning properly. Ensure the regulator shows no signs of physical damage or corrosion before installation.
What is another name for the point pressure leak test?
The point pressure leak test, also known as the Valsalva leak test
What do you do to find out how the fuel is getting into the oil?
Assuming this vehicle is fuel injected, you can do a leak down test.
Where can you find a vacuum line to test with a dye checker if you have a blown head gasket or not its a 1998 aurora?
have a leak down test done its more reliable,
How do you change ignition switch on 2000 Harley Davidson road king?
To change the ignition switch on a 2000 Harley Davidson Road King, first disconnect the battery to ensure safety. Remove the switch assembly by unscrewing the retaining screws and disconnecting the wiring harness. Install the new ignition switch by connecting the wiring harness and securing it with screws. Finally, reconnect the battery and test the new switch to ensure it operates correctly.
