0
Yes, in California, the sale of baling twine is generally subject to sales tax because it is considered tangible personal property. However, if the twine is sold for agricultural use and meets certain criteria, it may be exempt from sales tax under certain agricultural exemptions. It's advisable to consult the California Department of Tax and Fee Administration or a tax professional for specific circumstances and compliance.
What else can I help you with?
What has the author Ann Y Etter written?
Ann Y. Etter has written: 'Baling twine & burlap bags' -- subject(s): Social life and customs, Farm life
How do you thread a 270 hay baler?
To thread a 270 hay baler, first, ensure the baler is properly set up and the twine is loaded onto the spool. Pull the twine from the spool and guide it through the tensioner and around the bale chamber, following the specific threading path indicated in the owner's manual. Make sure to secure the twine in the appropriate clamps or guides to ensure it feeds correctly during operation. Finally, test the mechanism to ensure the twine is properly threaded and ready for baling.
How do you thread a 124 Massey baler?
1. put the twine in the twine box and pull twine from the ceter of the ball. 2. pass the twine through the guides in the lid of the twine box and then through the guides at the left rear of the twine box, through the holes to the outside of the box and through the tensioner (the little plate with the spring on it), through the guide at the bottom of the box, to the left of the spring bracket, throught the eye of the take-up spring, through yet another guide, and then one last guide at the end of the needle, through the eye of the needle and tie the twine off to the cross member to anchor it in place. 3. repeat for the other side. 4. now trip the knotters and the needles will bring the twine up to the knotters and put it in the twine grip. 5. go to baling, if the knotters are set correctly it should start tieing the string. 6. best bet is to buy the operators manual for it, it is a real time saver to have.
268 new holland baler will only tie one side the other is a slipnot why?
no knot on the end of twine held by the twine holder 1-need more tension on twine holder spring or 2- baling too tight no knot on twine on the end delivered by the needles 1-twine disc timing (this is the most likely cause) look at the other disc to see if it ia aligned the same as the one that's working and check arm to see if it's bent different than the side that's working - also ck the mounting of the twine finger to see if it's farther back than the one working--also ck the hay dogs--hope this helps!!---been there done that---haha --- Randy
Easy diy twine rug?
Diy twine rugs are easy crafts that you can make out of twine by braiding.
Where does twine come from?
Twine is made from both plants and synthetic fibers. The two products are mixed to together to make the final twine product.
How do you use twine as a sentence?
I used twine to help my dad.
How do you get twine on FarmVille?
The collectible twine can be found when harvesting sheep on your farm.
Where is the object twine located in sims 2 castaway?
Twine is not an object or a plant. You find sisal first, then you make twine on a crafting bench.
Is twine recyclable?
If the twine is made from a natural fiber, like hemp, sisal or even cotton, then it is biodegradable.Some twine is made of plastic. This is not biodegradable.
What has the author F Twine written?
F. Twine has written: 'Low pay in Scotland'
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
