0
If your Massey Ferguson 12 baler is experiencing twine breaks after each cut, it could be due to several factors. Check the twine tension settings to ensure they are correct, as too much tension can cause breaks. Additionally, inspect the twine for damage or improper threading, and ensure that the knife and cutting mechanism are sharp and functioning properly. Lastly, consider the type and quality of twine being used, as subpar materials can also lead to frequent breakage.
What else can I help you with?
What year is your Massey Ferguson tractor Serial?
To determine the year of a Massey Ferguson tractor, you can find the serial number usually located on the tractor's chassis or under the seat. Each model has a specific range of serial numbers corresponding to production years. You can cross-reference the serial number with Massey Ferguson's official documentation or online resources to identify the exact year of manufacture. If you provide the serial number, I can help with more specific information!
What year mf135 94006?
The MF135 is a model of tractor produced by Massey Ferguson, and the number "94006" typically refers to a serial number. The MF135 was manufactured between 1964 and 1975. To determine the exact year of a specific MF135 with the serial number 94006, you would need to consult Massey Ferguson's serial number chart, as each number corresponds to a specific production year within that range.
How do you thread a Massey Ferguson model 12 square baler?
first your two roll in their compartment,run under the little plate before exiting and then going thru the two tension aid springs and then both thru the 1st porcelain,then divide for each porcelain on needle and go tie at base of needle and then engage manually for tiyng knot and then rotate whole system by hand by turning the flywheel.Gidday, I am self-taught on the 503, but after threading the needle, I pass the twine straight up through the gap in the knotting mechanism, against the thingy with the multiple serrated discs, then tie it back to the bale density adjuster at the back. After the first bale it will cut the twine then you can remove the remaining bit of twine with the knot you tied.
What kind of fluid goes in a Massey Ferguson 230 transmission and rearend and how much in each?
The Massey Ferguson 230 typically uses a universal tractor transmission fluid or a multi-purpose hydraulic fluid, such as UTF (Universal Tractor Fluid). The transmission and rear end combined capacity is approximately 8 gallons (30 liters). It's essential to consult the operator's manual for specific recommendations and to ensure proper maintenance.
How can you tell what the rear brakes are on 135 MASSEY FERGUSON?
To identify the rear brakes on a 135 Massey Ferguson, locate the brake housing on each rear wheel. The brakes are typically drum-type and are accessed by removing the wheel and brake drum cover. You can also refer to the tractor's service manual for detailed diagrams and specifications. Additionally, visual inspection may show brake lines leading to the brake assembly, indicating their location.
How do you set the timing on Massey Ferguson 12 hay baler?
first your two roll in their compartment,run under the little plate before exiting and then going thru the two tension aid springs and then both thru the 1st porcelain,then divide for each porcelain on needle and go tie at base of needle and then engage manually for tiyng knot and then rotate whole system by hand by turning the flywheel. Gidday, I am self-taught on the 503, but after threading the needle, I pass the twine straight up through the gap in the knotting mechanism, against the thingy with the multiple serrated discs, then tie it back to the bale density adjuster at the back. After the first bale it will cut the twine then you can remove the remaining bit of twine with the knot you tied.
Is chris Massey and kyle Massey brothers?
yes, because they look and talk like each other
How do you change the screens on a Massey Ferguson grinder mixer model 15?
Open the mill and remove and replace the screen. You shouldn't need any tools as the mill lid is held in place by a couple of t-bolts - one on each side.
How do you adjust valve clearance on Massey Ferguson 390?
To adjust the valve clearance on a Massey Ferguson 390, first, ensure the engine is cool and remove the valve cover. Rotate the engine to bring the piston of the cylinder you are adjusting to the top of its compression stroke (TDC). Using a feeler gauge, check the clearance between the rocker arm and the valve stem, adjusting as necessary by loosening the lock nut and turning the adjusting screw to achieve the specified clearance. Repeat this process for each cylinder, then reassemble and torque the valve cover properly.
How do you you thread a new holland 310 hay baler?
Place two rolls of twine into the twine chamber, pull the end of the twine from the center of the rolls. Thread the twine from each roll through the loops in the lid of the twine chamber. Each twine should go through the loop on the side of the lid that the roll of twine sits on. The left side through the left loop, the twine on the right side through the right side loop. Run the twine through the two tubes on the left side of the twine chamber. The again, the left through the left side, the right through the right side. Close the lid to the twine chamber. Run the ends of the twine through the porcelian electric insulator fastened to the needle carriage, then the ends of the twine through the eyes of the needles. Again, the twine from the left side through the left needle eye, the end of the twine from the right side through the eye of the right needle. Pull the ends back to the protective pipes surrounding the needles and tie the ends to the pipe. Raise the bale trip lever on the drivers side of the bale chamber so it will trip shortly after you power the baler. You will need a small amount of hay going through the chamber to do this. When the bale trip lever trips, the needles will come up and the knotters will grab the twine and hold it. You are now ready to bale.
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
How do you bleed the brakes on a Massey Ferguson 399 tractor?
To bleed the brakes on a Massey Ferguson 399 tractor, start by locating the brake bleeder screws on each brake cylinder. With the tractor parked on a level surface, have an assistant pump the brake pedal several times and hold it down. Loosen the bleeder screw to release any trapped air and fluid, then tighten it before your assistant releases the brake pedal. Repeat this process until you see a steady stream of brake fluid without bubbles, ensuring the brake system is fully bled.
