answersLogoWhite

0

NO. Because they are vinyl, they will expand and contract at a different rate than grout, which is essentially concrete. You are supposed to lay vinyl tiles tightly together, with no gaps in between.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

Why floor tiles have some gap at the middle?

Ceramic tiles have a grout "gap" but vinyl tiles shouldn't have a gap.


What cement should you use to put tile over vinyl floor tiles?

That would depend on whether they are ceramic tiles or more vinyl tiles.


How do I go about installing tile over vinyl flooring?

To install tile over vinyl flooring, first clean and prepare the vinyl surface. Then, apply a layer of thin-set mortar and lay the tiles in the desired pattern. Allow the mortar to dry completely before grouting the tiles. Finally, seal the grout to finish the installation.


What is the best method for cleaning and maintaining grout for vinyl tile flooring?

The best method for cleaning and maintaining grout for vinyl tile flooring is to regularly sweep or vacuum the floor to remove dirt and debris, then use a mixture of warm water and mild detergent to clean the grout lines. For tougher stains, a mixture of baking soda and water or a commercial grout cleaner can be used. It's important to avoid harsh chemicals that can damage the vinyl tiles. Additionally, sealing the grout lines can help prevent future staining and make cleaning easier.


What is weight of vinyl floor tiles?

What is the weight of Vinyl Floor tiles per m2


What are the best cleaning methods for maintaining vinyl grout in a bathroom?

The best cleaning methods for maintaining vinyl grout in a bathroom are to regularly scrub the grout with a mixture of water and mild detergent, use a soft brush or sponge to avoid scratching the vinyl, and rinse thoroughly with clean water. Additionally, applying a grout sealer can help protect the grout from stains and discoloration.


How do I go about installing vinyl tile flooring in my home?

To install vinyl tile flooring in your home, start by preparing the subfloor by cleaning and leveling it. Measure the room to determine how many tiles you will need. Begin laying the tiles starting from the center of the room and working outwards. Use adhesive to secure the tiles in place and ensure they are properly aligned. Finish by cutting tiles to fit around edges and corners, and apply grout if necessary.


How do I refinish my vinyl tile?

You start by weep the vinyl tiles with a broom. Then Wash the vinyl tiles with disodium phosphate, using a nylon pad. What you need to do next uis rinse vertical-running tiles with wet rags. Rinse floor tiles with a mop. Let the vinyl tiles dry for two hours.


What is homogeneous vinyl tile?

It is similar to roll vinyl or linoleum but cut into tiles.


What are the best methods for cleaning and maintaining vinyl tile grout to ensure its longevity and appearance?

The best methods for cleaning and maintaining vinyl tile grout include regular sweeping and mopping with a mild detergent, using a grout brush for deeper cleaning, applying a grout sealer to protect against stains, and avoiding harsh chemicals that can damage the grout. These practices will help preserve the grout's appearance and longevity.


Selecting the Best Vinyl Flooring for You?

Selecting vinyl flooring may not sound like that big of a deal, but there are actually a number of things that you should consider when you are deciding on what type of vinyl flooring to get. For example, consider the differences between using individual vinyl tiles and using vinyl sheeting. If you have a dog or live in an area that sees a lot of rain, you will likely be much happier with a sheet of vinyl flooring than a bunch of tiles. This is because in wet areas, water seeps down into the cracks that separate the tiles, causing them to warp and bend.


Can you put vinyl on top of tile?

No this is not advisable, As the tile has lines called grout lines, they are indented as is most of the tiles you buy. Then to ad the adhesive of the vinyl and then the vinyl you will have air trapped which will cause the vinyl to move , rip, and you wont like this either. It has to laid atop a clean dry dust and partical free area, as one tiny rock or nail head popping up can cause this to hole and tear.However you can apply Vinyl Tile Atop of Tile flooring as long as you make sure to level the floor. The two (bottom & top) tiles must be even and level for this to happen, see my insert for this:Inspect the ceramic tile for any loosened or damaged tiles. Repair small cracks or chips with liquid epoxy. Remove any severely damaged pieces and fill the gaps with liquid cement or mortar. Use only enough cement or mortar to bring the section even with the rest of the tiles; you must maintain a flat surface.2Mix grout and water as instructed with your specific product; different products will require different mixtures of each. Use a grout trowel to add grout to the joints between the ceramic tiles, until they are completely even with the tile surfaces. Wipe any excess grout from the joints or the tiles with paper towels. Adding grout to the joints will give you a completely flat surface.Sponsored LinksDIY Radiant Installation Easy to install radiant panels save time & money. Perfect for remodels.completeradiantpanel.com/3Install an underlayment if directed by your chosen vinyl product. Some vinyl tiles are designed to adhere directly to the old floor, while others will require a layer of plywood or other underlayment to control moisture and possible expansion or contraction.4Sweep the floor clean to remove any dust or dirt from grouting or installing the underlayment. Any dirt or dust left on the surface can ruin the way the new tiles adhere to the surface.5Lay vinyl tiles, beginning in the center of the floor and working your way out. If you are working in a large area, you may benefit from breaking the area into quadrants and working one section at a time.6Pull away the wax paper backing of self-adhesive tiles and carefully lay the tile in place, rubbing firmly across the surface to encourage the adhesive to stick. If you are working with tiles that do not self-stick, use a trowel to spread a thin, even layer of adhesive on the ceramic or underlayment and press the tiles in to place.7Cut tiles to size using a vinyl tile cutter to make tiles fit around vents or against the wall. Continue to install tile until the entire floor is covered.8Roll the entire floor surface with a baker's roller to ensure that all areas stick equally.9Allow the adhesive to dry for at least five days before washing, so that the glue has enough time to dry.