answersLogoWhite

0

Mr.Stoeber made the twine ball in 1953. there is your answer and i am a girl from your school pay very close attention to who i am.....

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

In what year did Mr. Stoeber start making the twine ball?

In 1953 mr. stoeber started making the twine ball.


What year did Mr Stoeber stat making the twine ball?

1953


What year did MrStoeber start making the twine ball?

Mr.Stoeber made the twine ball in 1953.


Where is the large ball of twine in Kansas?

The large ball of twine in Kansas is located in Cawker City. It was started in 1953 by a local resident named Frank Stoeber and has since grown to become a popular roadside attraction. The ball continues to be added to by visitors and locals, making it one of the largest of its kind in the world.


How do you thread a McCormick IH Forty Six baler?

THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.


How do you thread the twine on a 5580 hesston round baler?

To thread the twine on a Hesston 5580 round baler, first, ensure the baler is turned off and safely positioned. Start by opening the twine box and removing the twine spools, then thread the twine through the appropriate guides and around the tensioner. Next, pull the twine through the twine arms and ensure it is securely positioned in the knotters. Finally, close the twine box and perform a test run to ensure proper operation.


How do you thread the twine on a New Holland 273 baler?

To thread the twine on a New Holland 273 baler, first, ensure the baler is turned off and safely positioned. Start by opening the twine box and placing the twine spools onto their holders. Then, guide the twine through the tensioner and around the twine guides, leading it towards the knotters. Finally, thread the twine through the knotter mechanism as per the baler's manual instructions, ensuring it is properly secured before closing the twine box.


How do you prepare maguey in making twine?

To prepare maguey for making twine, first, the leaves of the plant are harvested and cleaned to remove any dirt. Then, the leaves are soaked in water to soften them, making them easier to work with. After soaking, the fibers are extracted by scraping the leaf with a tool to separate the strong fibers from the softer material. Finally, the fibers are twisted and braided together to create durable twine.


What is in sisal twine?

Sisal twine is made from the fibers of the sisal plant, specifically Agave sisalana. These natural fibers are known for their strength, durability, and resistance to deterioration, making sisal twine suitable for a variety of applications, including gardening, packaging, and crafting. The twine is biodegradable and environmentally friendly, offering a sustainable alternative to synthetic ropes and twines.


How can I effectively use plant twine to support and train my garden plants?

To effectively use plant twine to support and train your garden plants, start by tying the twine loosely around the base of the plant and then gently guide the stems along the twine as they grow. Regularly check and adjust the twine as needed to provide proper support and encourage vertical growth. This will help prevent the plants from bending or breaking under their own weight and promote healthy growth.


Can you name all the words that start with twi as a prefix?

Sure! Some words that start with "twi" as a prefix are twilight, twin, twine, and twirl.


Easy diy twine rug?

Diy twine rugs are easy crafts that you can make out of twine by braiding.