0
You first need to find the part. You want Toyota part #7736033020 (fuel door spring.) Most places will probably have to order it so you can save yourself some footsteps by calling ahead to your local Napa or other parts store. It should cost $5-$10. Once you have the part it basically just snaps on to the hinge inside of the fuel door. It fits about half way up the door with the small part of the "V" spring placed closest to the hinge. There are three points that need to be positioned. The outer end of the part (the large "V" end) curls under and clips on to the bracing on the lid, the other end has a small protrusion that slides under the flange portion that is attached to the car body. The third spot is a small notch that fits over, and clamps down onto, the hinge axis. If you only open the door about 1/4 of the way when installing the spring, everything will line up/clip on easier. Once the two ends are where they need to be, snap the spring into place by pressing the notched section down onto the hinge while holding the lid steady.
What else can I help you with?
What are all the parts to change the struts on Toyota Avalon 1998?
Strut mount, coil spring, coil spring isolator, rubber dust boot.
How do you replace valve seals on a Toyota Avalon?
To replace valve seals on a Toyota Avalon, first, remove the valve covers and the necessary components to access the cylinder heads, such as the intake manifold and spark plugs. Use a valve spring compressor to remove the valve springs and retainers, then gently pull out the old valve seals and replace them with new ones. Reassemble the components in reverse order, ensuring all parts are torqued to the manufacturer's specifications. Finally, check for leaks and ensure everything is functioning properly before starting the engine.
How do you take the ashtray assembly out of a 96 Toyota Avalon?
most ashtrays have a spring loaded tab that pushes down and then you slide it out. This is also how it returns back in...
How do you replace the spring in the trigger mechanism in a marlin 49dl 22 semi automatic rifle?
Best left to a gunsmith.
How do you replace footrest spring in a recliner?
To replace the footrest spring in a recliner, first, remove the recliner's fabric or upholstery to access the mechanism. Next, detach the old spring by unhooking it from its attachment points. Then, hook the new spring in place, ensuring it is securely fastened. Finally, reassemble the recliner and test the footrest to confirm proper operation.
Where is the spring in the door lock in the Toyota Previa 1992?
In the 1992 Toyota Previa, the spring in the door lock mechanism is typically located within the door latch assembly. It functions to return the lock to its default position after being actuated. To access it, you usually need to remove the door panel and then disassemble the latch mechanism. Always refer to a service manual for detailed instructions specific to your vehicle model.
How do you replace the fuel door spring on a Lexus es300?
To replace the fuel door spring on a Lexus ES300, first, open the fuel door and locate the spring mechanism. Carefully remove any clips or screws securing the spring in place, then detach the old spring. Install the new spring by aligning it with the mounting points and securing it with the clips or screws. Finally, test the fuel door to ensure it opens and closes properly.
How do you install new rear struts on a 2005 Toyota Camry?
Strongly advise you to have this done. Even if you can get the strut removed from the car,you will need a spring compress to remove/replace spring. There is a lot of energy in a spring and you can be seriously injured or killed if spring is not properly handled.
How do you replace belts on 1994 Toyota corolla?
There is only one belt, the serpentine belt. You use a wrench to loosen the spring loaded tensioner and remove and replace, there is no timing belt it has a chain.
Why won't my bike brake spring back into place?
Your bike brake may not spring back into place due to issues such as a worn-out spring, misaligned brake pads, or dirt and debris clogging the brake mechanism. It is important to inspect and possibly replace the spring or clean and adjust the brake components to ensure proper function.
How do you replace the shifter spring?
To replace the shifter spring, first, disconnect the shifter from the vehicle's power source and remove any necessary panels to access the shifter mechanism. Carefully take out the old spring, noting its orientation for proper installation of the new one. Install the new spring in the same position as the old one, ensuring it is securely placed. Reassemble any panels and reconnect the shifter to the power source.
How do you replace the spring in the latch on KIA 2001 glove compartment?
To replace the spring in the latch of a 2001 KIA glove compartment, first, remove the glove compartment door by unscrewing the screws that hold it in place. Once the door is off, locate the latch mechanism and carefully detach the old spring. Replace it with a new spring by attaching it to the same points as the original, ensuring it is secured properly before reassembling the glove compartment door. Finally, reattach the screws to secure the door back in place.
