answersLogoWhite

0

Found this online, this worked on my wife's 2000 Protege:

Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Close and open the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 2x. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 2x (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What size speakers are in a 2003 Mazda Protege?

6x9 in the front doors 6.5 in the back doors


You took out a deck from your 03 Mazda protege and the radio and your remote to unlock the doors wont work any help?

Have you tried to put it back? It may just work, if you want to replace the radio I would bring it to the dealer


Is a 98 Mazda 626 fuel door the same size as a 98 Mazda Protege fuel door?

Hi! The fuel doors are not the same size.


Are the rear doors in a 2000 Mazda protege prewired to install speakers?

Que son los glóbulos rojos alto


Why remote key not unlock Mazda 6?

One reason that your remote key will not unlock your Mazda 6 is that a fuse is blown. You may need to replace the batteries in the remote or reprogram the remote. A bad body control module is another reason the remote will not unlock the doors.


How do you program a keyless entry remote for a 1996 Ford F-250?

It is necessary to have ALL (maximum of four-original and/or new) of your remote transmitters available prior to beginning this procedure To program the transmitters yourself: # Insert a key in the ignition and turn from 3(Off) to 4(On) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4(On) position. # The doors will lock/unlock to confirm that programming mode has been entered. # Within 20 seconds, program a remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.) # Repeat the previous step to program additional remote transmitters. The doors will lock/unlock to confirm that each remote transmitter has been programmed. # When you have completed programming the remote transmitters, turn th ignition to 3(Off) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed. That's it!


How do you program alarm remote transmitter of Subaru Outback 05?

See "Sounding a Panic Alarm" on page 15 in Chapter 2 "Keys and Doors" of your "OWNER'S MANUAL".....


How do you reset the alarm in a Ford Explorer Trac 2001?

To reset the alarm on the remote transmitters:Have ALL of your transmitters available before you begin this procedure.Put the key in the ignition and turn from 2 (lock) to 3 (off) and cycle between 3 (off) and 4 (on) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4 (on) possition. The doors will lock/unlock to confirm that programming mode has been entered.Within 20 seconds, program a remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.)Repeat the previous step to program additional remotes. The doors will lock/unlock to confirm that each remote has been programed.When you have completed programming, turn the ignition to 3(off). Again the doors will lock/unlock to confirm programming has been completed.


Why are the digital odometer numbers still displayed when 2000 Mazda Protege ignition is turned off?

the display stays on for about a minute or so after all the doors have been closed. at least that's what ive noticed on my 2000 protege. its nothing that will drain your battery though.


How do you Program doors remote transmitter for Toyota Tundra 2001?

if you have taken the battery out of your remote you will have to take it to the dealer it has no memory after you take the battery out. dealer told me if i would have changed it out in about 5 seconds it might have saved its memory. i found out the hard way


Services?

Garage Door Spring, Garage Door Opener, Garage Door Remote Transmitter, Insulated Garage Doors, Automatic Garage Door Repair, Roll Up Garage Doors, Residential Garage Doors, Commercial Garage Doors, Garage Door Cable Replacement, Replacement Garage Door Panels


How do you program your keyless remote control fob for a Ford Windstar?

This procedure is detailed and illustrated in the Owners Manual - See "Related Questions" below for moreI know this sounds silly but it does work.To program the transmitters yourself:Insert a key in the ignition and turn from 3(Off) to 4(On) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 4(On) position.The doors will lock/unlock to confirm that programming mode has been entered.Within 20 seconds, program a remote transmitter by pressing any button on a transmitter. The doors will lock/unlock to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.)Repeat the previous step to program additional remote transmitters. The doors will lock/unlock to confirm that each remote transmitter has been programmed.When you have completed programming the remote transmitters, turn th ignition to 3(Off) or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.Turn Ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. All doors will lock then unlock to confirm programming mode. Within 20 seconds, press any button on remote transmitter. Door locks will cycle to confirm programming. Turn ignition to OFF. Locks will cycle again to indicate end of programming mode.The instructions above DO work ! It IS that simple! So, please folks, just follow the instructions above. PLEASE don't pay some jerk on Ebay for the instructions.