answersLogoWhite

0

Do what I did. Run a wire from the fuse block's main input cable, (positive) into the interior, run another wire from the starter solenoid into the car's interior and connect them to a switch or touch them together to turn the engine over. Make sure when you turn your key on to turn it all the way so the security system won't disable the vehicle. Oh ya, make sure its not ingear.

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

Does a 92 Isuzu pickup have a fuse to the clutch starter safety switch?

No


How can the clutch switch be bypassed on a 1986 Isuzu pickup?

This is a safety issue but if you do it just connect the wires together.


How do you remove the ignition switch in a 1988 Isuzu pickup?

how to remove lock cyliner switch 1988 Isuzu pickup


Where is the ecm in a 1991 Isuzu pickup?

It is to the left of the clutch pedal,under the plastic cover,behind the carpet.


How do you change the clutch in a 1989 Isuzu pickup?

To change the clutch in a 1989 Isuzu pickup, first, disconnect the battery and remove the transmission by unbolting it from the engine and separating it from the driveshaft. Next, take out the old clutch assembly, including the pressure plate and disk. Install the new clutch components, ensuring proper alignment, then reattach the transmission and driveshaft. Finally, reconnect the battery and test the clutch operation before driving.


Installation clutch cable 1990 Isuzu pickup?

To install a clutch cable on a 1990 Isuzu pickup, first, disconnect the negative battery cable for safety. Then, remove the old clutch cable by detaching it from the clutch pedal and the transmission. Install the new cable by threading it through the firewall and connecting it to the pedal and transmission, ensuring proper tension. Finally, adjust the cable if necessary and reconnect the battery.


How do you adjust clutch in 1997 Isuzu pickup?

To adjust the clutch in a 1997 Isuzu pickup, first, ensure the vehicle is on a level surface and the engine is off. Locate the clutch master cylinder, which is usually near the firewall; check the fluid level and top it off if necessary. Then, adjust the clutch pedal free play by loosening the lock nut on the pushrod and turning the pushrod to achieve about 1-2 inches of free play at the pedal before resistance is felt. Finally, tighten the lock nut and test the clutch operation before driving.


Isuzu wiring diagram?

radio 1990 isuzu pickup


How do you repair clutch when firewall is cracked 1991 Isuzu pickup?

To repair a cracked firewall on a 1991 Isuzu pickup affecting the clutch, first, remove the necessary components obstructing access to the firewall, such as the dashboard and pedals. Clean the cracked area thoroughly, then reinforce it with a metal patch or fiberglass for added strength. Use a strong adhesive or welding method to secure the patch in place, ensuring it’s properly sealed to prevent further damage. Finally, reassemble the components and test the clutch operation.


What is the psi on the 1990 v6 Isuzu pickup fuel pump?

what's the pis of the 1990 v6 isuzu pickup fuel pump


What are the names of some Isuzu pickup trucks released in the US?

Isuzu Motors Ltd. is a Japanese automobile manufacturer. The Isuzu Amigo and the Isuzu Hombre are two of the pickup trucks this company manufactures and sells in the United States.


1992 Isuzu Rodeo Brake and rwal dash lights on?

I have a 1991 Isuzu pickup with rwal - there is control box (sender switch) that has to be re-set. I'd take it to the dealer and they can re-set it in a few minutes. It usually lasts for 100k. good luck! I have a 1991 Isuzu pickup with rwal - there is control box (sender switch) that has to be re-set. I'd take it to the dealer and they can re-set it in a few minutes. It usually lasts for 100k. good luck!