answersLogoWhite

0

To change the master window switch on a 1998 Acura RL, first, remove the panel surrounding the switch by carefully prying it up with a trim tool or flathead screwdriver. Disconnect the electrical connector from the back of the old switch and then remove the switch from the panel. Install the new switch by connecting the wiring harness and securing it in place, then reattach the panel. Finally, test the new switch to ensure it operates correctly.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

Is your 92 Acura Integra master window switch interchangable?

The 1992 Acura Integra master window switch is interchangeable with other 1992 models. The master window switch was used in all 1991 through 1994 models.


How do you replace the driver's side electric window switch on a 1992 Acura Integra?

The driver side electric window switch on a 1992 Acura Integra is reached by removing the door panel. Unbolt the switch from the mounting bracket and disconnect the wiring from the harness. Replace the unit.


How do you Reset the power window sensor Acura RSX?

To reset the power window sensor on an Acura RSX, first ensure the ignition is turned on but the engine is off. Then, fully lower the window by holding the window switch down, and once it reaches the bottom, hold the switch down for an additional few seconds. Next, pull the switch up to close the window completely, and once it's fully closed, hold the switch up for a few more seconds. Repeat this process for each window to ensure proper resetting.


How do you remove power window switch from 1999 Acura Integra?

To remove the power window switch from a 1999 Acura Integra, first, ensure the vehicle is turned off and disconnect the negative battery terminal to prevent any electrical issues. Carefully pry off the switch panel using a flathead screwdriver or trim removal tool, starting from one edge. Once the panel is loose, disconnect the wiring harness from the back of the switch, then you can remove the switch from the panel by pressing the tabs on the sides. After that, the switch can be replaced or repaired as needed.


How do you fix the rear power window on Acura MDX?

how do i fix the rear passenger window of my acura mdx


How do you change VSA switch in Acura MDX?

To change the VSA (Vehicle Stability Assist) switch in an Acura MDX, first disconnect the negative battery cable to ensure safety. Remove the trim panel around the switch, then unscrew or unclip the old switch from its mounting. Replace it with the new switch, reattach the trim panel, and reconnect the battery. Ensure the switch functions correctly by testing it after installation.


If you roll down your driverside window in your 91 acura legend and its fine but it wont go up what is it?

it sounds to me like the switch is bad i had a Mercedes with the same problem it would go down but not back up and i finally replaced the window switch and now it works fine


How do you change the key cylinder of the ignition switch in a 1991 acura legend?

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.


Do you need any special tools to change a window in a 1988 acura legend?

no a Philips screw driver and a 10mm socket


How do you change master cylinder Acura Vigor?

Disconnect fluid linesRemove mounting boltsSlide cylinder out of booster REMEMBER TO BENCH BLEED NEW MASTER CYLINDER PRIOR TO INSTALLATION


Brake light stays on How can you FIX THIS 1991 Acura Legend?

You will need to change the brake light switch. The brake light switch can be found below the dashboard on the drivers side.


How do you fix the rear power window on a 2004 Acura MDX?

To fix the rear power window on a 2004 Acura MDX, first, check the fuse associated with the power windows to ensure it’s not blown. If the fuse is fine, remove the door panel to access the window motor and regulator. Test the motor with a multimeter to see if it's receiving power; if not, you may need to replace the window switch or wiring. If the motor is faulty, replace it to restore functionality.