0
On the 95-98. Open the trunk. The screws (2) are just inside the trunk. After you remove them, very carefully push outward in the lens. The lens has a pin on the outer side that sticks into the car body. This pin can stick, so be very careful not to break something.
On my 2002 Protege ES, the process is a bit different
There are two plastic retainer do-hickeys on the hard that are made up of an inner circle and outer ring. Both of these are easily visible.
They are removed by first loosening the inner circle (probably moves back about 1cm), and then the whole do-hickey can be removed by gently prying the outer rings.
The hard vinyl still feels attached, so you can move it/lift it by hand until it moves over the rear release latch. This gives you enough room to operate.
The hard cloth (who's edge is covered by the vinyl) has two of those plastic retainer do-hickeys. Remove them too. Then you can access the back of the assembly/sheet metal.
Then there are three brass-ish long screws with 10mm nuts. Remove those three nuts, and you can pull out the tail light assembly.
What else can I help you with?
How do you change marker light bulb in Mazda Protege?
To change the marker light bulb in a Mazda Protege, first, open the hood and locate the light assembly. Remove the screws or clips securing the assembly and gently pull it out. Disconnect the wiring harness from the old bulb, twist the bulb socket counterclockwise to remove it, and replace it with a new bulb. Reconnect the wiring, reassemble the light assembly, and test the new bulb before closing the hood.
How do you change a mazda protege license plate light bulb?
To change the license plate light bulb on a Mazda Protege, first, locate the license plate light assembly at the rear of the vehicle. Use a flathead screwdriver to gently pry open the assembly cover. Remove the old bulb by twisting it counterclockwise and then insert the new bulb, making sure it’s secure. Finally, replace the cover and ensure the light functions properly.
How do you change the license plate light bulb on Mazda protege?
There are two housings above the plate all you need is a Phillips head screw driver remove the 4 bolts and change the bulbs it's that easy
How do you change the parking light in a 2003 Mazda protege?
To change the parking light in a 2003 Mazda Protege, first, open the hood and locate the back of the headlight assembly. Remove the screws or clips holding the assembly in place and carefully pull it out. Twist the parking light socket counterclockwise to release it, then replace the old bulb with a new one. Reassemble the headlight assembly and ensure everything is secured before closing the hood.
How do you change the lowbeam headlight bulb on a mazda protege 5?
Open Hood. Open the hood of your Mazda 5. The hood release is located under the dashboard of your 5.
How do you change the light bulb in the gear shift indicator Mazda 6 2005?
What is the bulb sizes
How do you change the drivers side marker light bulb in a 2005 Mazda 6?
what year? and which parking light? side marker or in the headlight? 2005 Mazda 6 side marker light bulb
How do you change tail light bulb on 2003 Mazda protege 5?
Basically, there are three bolts that you need to take out. Then you pull off the tailight assembly. Replace the bulb as required and then replace the taillight on the car ncmuding any bolts you removed. Refer to your owner's manual.
How do you change a right rear turn signal bulb on a 99 Mazda Protege?
1999 Mazda Protege turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).
How do you replace the license plate lights on a 1999 Mazda protege?
Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.
Is it necessary to remove the tail light assembly to change the tail light bulb on a Mazda MPV?
Yes unfortunatly
How do you access the 3rd brake light on a 1988 Mazda 626 to change the bulb?
From inside the trunk.
