* Loosen the front wheel lug nuts,raise the front of the car and support it securely on jackstands and remove the front wheels * Detach the brake hose bracket from the strut.If the car is equipped with ABS detach the speed sensor wiring harness from the strut by removing the clamp bracket bolt * Remove the strut to knuckle nuts and if nessary knock the bolts out with a hammer and punch * Separate the strut from the steering knuckle.Be careful not to overextend the inner CV joint dont let the knuckle fall outward as this may damage the brake hose * An assistant would be helpful at this point to hold the strut as the nuts are loosened.Remove the strut upper mounting nuts.Remove the assembly out of the fenderwell
how change front strut on1995 Oldsmobile catlass suprime
To change the rear strut on a 2002 Hyundai XG350, start by safely lifting the vehicle and securing it on jack stands. Remove the rear wheel, then disconnect the lower strut bolt and the upper strut mount bolts inside the trunk. After detaching the strut assembly, replace it with the new strut, reattach the upper and lower bolts, and finally, reinstall the wheel. Always ensure the suspension is properly aligned after completing the replacement.
To replace the front struts on a 2000 model Hyundai Sonata, you will first need to remove the tires. There will be 3 nuts on top of the strut mount. You will need to remove the 2 bolts that connect from the strut to the knuckle. Then you will need to remove the ABS sending unit as well as the front brake hose. Once these components are removed, you can remove the strut. In order to remove the strut, you will need a special tool to compress the spring. Once the struts are removed, you can safely replace them with new struts.
To change the front strut it is not hard at all. Simply remove the tire, remove the break, remove the bottom bolts from the strut. Then remove the top bolt from the strut. Usually takes about 20-40 minutes to remove. Replacing is very simple as well. However, the front strut replacement will require a front-end alignment to be completed.
Use a strut spring compressor to compress the old spring, the remove the strut from the spring. Use the compressor to put the strut into the new spring. Install the strut and spring into the vehicle.
You will need to compress the 2002 Pontiac Grand Am strut spring with a spring compressor. Remove the top and bottom strut retaining bolts. Reverse the process to install the new strut.
Be sure to consult a manual before attempting any car repair. Locate the struts directly in front of the rear wheel well. Follow the brake hose from the wheel hub, and pull the strut assembly out of the bottom of the car. Disassemble the strut assembly, and replace the shocks and any other places showing wear. Reassemble the strut and replace it in the car.
to change a front wheel bearing remove macpherson strut and press out bearings with a press, replace with press.
To change the front struts on a 2000 Nissan Quest, start by safely lifting the vehicle and removing the front wheels. Next, disconnect the strut assembly from the steering knuckle and the upper strut mount, which may require removing the strut tower cover for access. Replace the old strut with the new one, reassembling in reverse order. Be sure to torque all bolts to the manufacturer's specifications and align the vehicle afterward.
To change the front struts on a 2003 Pontiac Sunfire, first, safely lift and support the vehicle, then remove the front wheels. Disconnect the sway bar link and the lower strut bolt, then remove the upper strut nuts from the strut tower inside the engine bay. Once the old strut is free, replace it with the new strut, reassemble everything in reverse order, and ensure all bolts are torqued to specifications before lowering the vehicle. Remember to check wheel alignment after completing the job.
Hi, Just finished the front strut work on my 1998 Hyundai Accent Hatchback. Step 1: Take off the tire. Step 2: Unscrew the Caliper bolt near the bottom of the caliper (Make sure you get a block for the caliper to rest on) Step 3: Unscrew the 2 Strut Bolts holding the strut in place (Before you do that, take a screwdriver and mark where the strut was sitting for when you bolt it back on) Step 4: Unscrew the upper strut nuts (3 of them and they are under the Bonnet) Step 5:Take the strut assembly out. Step 6: Use a spring compressor to compress the spring until there is no force on the upper strut mount. Step 7: Unscrew the nut holding the upper strut mount in place with your Impact and take the mount off. Step 8: Take tension off of the old spring and put a new one on using the same technique. Other than that, you reverse these steps and your done!!
To change the front struts on a 2003 Jetta, start by safely lifting the vehicle and removing the front wheels. Next, detach the strut assembly by loosening the bolts at the top of the strut mount and the lower control arm. Replace the old strut with the new one, ensuring everything is tightened to the manufacturer’s specifications. Finally, reassemble the components, reinstall the wheels, and lower the vehicle back to the ground.