0
How do you change the rear struts on a Toyota solara how do you get to the top bolts?
You'd be well advised to pick up a Chilton manual or Toyota factory service manual for a step-by-step description with photos.
Without knowing which of the two generations of Solara you're asking about an accurate answer is difficult. For the Gen II Solara (2004 and later) you simply remove the rear seat and (in the sedan) package shelf to remove the three nuts securing the rear strut. Caution, there are other pieces that are attached to the strut and rear axle that should be loosened or removed as well. That's where a proper manual will help prevent expensive breakage.
Cheers
What else can I help you with?
How do you replace rear struts on 1999 Toyota solara?
The 1999 Toyota does not have rear struts. The automobile has rear shocks. Remove the retaining bolts from each end of the shock. Reverse the process to install the new shock.
How do you replace rear strut on a 1999 Toyota solara?
The 1999 Toyota does not have rear struts. The automobile has rear shocks. Remove the retaining bolts from each end of the shock. Reverse the process to install the new shock.
How do you replace hatchback struts on 2000 Toyota Celica?
buy them from amazon and change them yourself you will save a fortune!. Change one at a time, just remove the bolts and replace...its easy!
How do you change a evap canister on a 2000 Toyota solara sle?
To change the EVAP canister on a 2000 Toyota Solara SLE, first ensure the vehicle is safely lifted and supported. Disconnect the battery, then locate the canister, typically found near the fuel tank. Remove any mounting bolts, disconnect the vacuum lines and electrical connectors, and then take out the old canister. Install the new canister by reversing these steps, ensuring all connections are secure before reconnecting the battery.
How do you change rear struts on a 300M?
The Chrysler 300 rear struts are held in place with a retaining bolt on each end of the strut. Remove the retaining bolts and the strut will come off. Reverse the process to install the new rear struts.
How do you change back license plate on Toyota solara?
Assuming you're in the U.S. (other countries may have different attachment schemes) face the plate. Notice there are two bolts or screws at the top holding the plate to the car. Unscrew the bolts. Remove the plate. Reverse procedure to attach new plate. Done. Cheers
How do you remove the headlamp assembly on a 2000 Toyota Solara?
To remove the headlamp assembly on a 2000 Toyota Solara, start by opening the hood and locating the headlamp assembly. Remove the screws or bolts securing the assembly, typically found on the top and side of the unit. Disconnect the electrical connectors and gently pull the headlamp assembly out of its housing. Be cautious not to damage any clips or wiring during the process.
How do you change front shocks on Toyota pickup 2wd?
Remove 3 bolts, remove shock, insert shock, compress shock, replace bolts
How do you replace struts on 2004 expedition?
The struts on a 2004 Ford Expedition are replaced by jacking the vehicle up, removing the wheels, and removing the strut retaining bolts. The old struts can then be removed and new struts put in their place.
How do you change the clutch fan on 1999 Toyota 4 runner?
12mm wrench on the four bolts behind it
How do you change struts on a 1993 Chevy Cavalier?
Begin by compressing the strut spring with a spring compressor. Be very careful as the strut spring will be under hundreds of pounds of pressure. Remove the strut retaining bolts. Reverse the process to install the new struts.
How do you replace the rear struts on a 2000 Toyota Corolla?
In the 8th Generation Corolla, 1998 to 2002, it's a pain. You must remove the back seats, because that is where the bolts that hold the struts are accessed. Then jack up the car and remove rear wheels. You possibly can access the bolts on the struts without taking the wheels off, but it's easier with them off) Please support the car properly for safety Do not use the tire change jack. Unbolt the bottom of the strut, and remove brake line (not from the brakes just unclip it from the strut, it's attached) Go back inside and unbolt the three bolts from the strut and pull up and out from inside the car. Install new struts same way opposite. (note: They are really more of a shock absorber than a MacPherson strut, you will not need a strut compressor for installation)
